|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
06-14-2020, 11:26 PM | #1 |
Not Yet Wild
Join Date: Jun 2020
Location: Hawaii
Posts: 9
|
Is this wired right?
Well ladies and gentlemen,
My new farm cart! It was on a dairy farm for 2 years in the junk pile. Pulled it out gave the lady some cash and hauled her home. Got told today its Ezgo 2000 TXT Standard. Dont know what that means... I have downloaded the manuals here on buggies gone wild and notice its wired in a series fashion. Controller is a curtis 25864G05. My question to you all, are those wires in the right place? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-16-2020, 12:17 AM | #2 |
Not Yet Wild
Join Date: Jun 2020
Location: Hawaii
Posts: 9
|
Re: Is this wired right?
I think this is the Drawing?
|
06-16-2020, 08:38 AM | #3 |
Gone Wild
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,544
|
Re: Is this wired right?
Looks correct to me.
Sent from my SM-G970U using Tapatalk |
06-16-2020, 10:15 AM | #4 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,417
|
Re: Is this wired right?
The blk wire from controller B- to solenoid small negative may be an addon. Does the cart run?
|
06-16-2020, 10:45 AM | #5 |
Not Yet Wild
Join Date: Jun 2020
Location: Hawaii
Posts: 9
|
Re: Is this wired right?
The cart does not run. I did all voltage checks. Everything checks out normal. In the parts list it says White wire on solonoid from power harness? I dont have a white wire?
|
06-17-2020, 11:03 AM | #6 |
Not Yet Wild
Join Date: Jun 2020
Location: Hawaii
Posts: 9
|
Re: Is this wired right?
The Blk wire from B- was on the drawing. The second one goes to the beeper.
|
06-19-2020, 12:33 PM | #7 |
Not Yet Wild
Join Date: Jun 2020
Location: Hawaii
Posts: 9
|
Re: Is this wired right?
Took the Blk wire off B- voltage checks ok. Any other suggestions?
|
06-20-2020, 12:56 AM | #8 |
Not Yet Wild
Join Date: Jun 2020
Location: Hawaii
Posts: 9
|
Re: Is this wired right?
I did this test that JohnnieB suggested to another member and my DVM read 2.8 volts at the controller (B- and M-) and as the pedal was pushed down it went into the negative. I followed the flow chart of voltage and all the other contact points read battery voltage, except C on the forward and reverse controller or A2 from the motor.
Can someone help me out on this one??? Bigb Test Suggested: Connect your DVM between the controller's B- and M- terminals. Charger not plugged into cart, key ON and F/R in F. Push pedal just far enough to make solenoid click and you should read full battery pack voltage (38.2V if fully charged). If you don't get the voltage, leave the Black test lead on the B- terminal and go looking for the missing voltage with the Red test lead. Attached is a series drive schematic with the high current circuit highlighted. |
06-23-2020, 01:21 AM | #9 |
Not Yet Wild
Join Date: Jun 2020
Location: Hawaii
Posts: 9
|
Re: Is this wired right?
Thank you JohnnieB!
The wire tracing from B- and M- worked. My Battery - was bad and that led me to trace wires from there. The wire trace led me to F/R not fully opening and closing the mico switches. Did the adjustments on the nuts and bolts and my cart came to life! Thanks JohnnieB! |
|
|
Similar Threads | ||||
Thread | Forum | |||
Wired DCS find | Electric EZGO | |||
48v ds wired incorrectly? | Electric Club Car | |||
Is this wired correctly? | Electric EZGO | |||
crossed wired | Electric EZGO | |||
need wired | Gas EZGO |