|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
12-18-2019, 08:09 PM | #1 |
Getting Wild
Join Date: Dec 2018
Location: Maine 8/ Florida 4
Posts: 129
|
Secondary clutch compression trick
Necessity being the mother of invention, and me not having a clutch compression tool, I improvised using one of the two basic tools in everyone’s shop...duct tape. This was on a Yamaha G22, but I’m sure it will work on many other applications. Starting with a 4 1/2” long by 3/4” diameter bolt in a vise, next a flat washer then your spring seat, spring and sliding sheave followed by another flat washer and the nut.(obviously the spring is placed in the proper holes for your desired performance) Tighten the nut till there’s just enough room to move the sliding sheave ramps over the ramp shoes, rotate the sliding sheave into position, (I could hold it with one hand, but its a little tricky) then tighten the nut down till the ramp tops are even with the plastic shoe tops(slightly more compressed than Its normal position when on the cart). Take the assembly out of the vise and turn it over, then tape across one side of the sheave face, up over the spring seat, and back around to the other side of the sheave face. I put one strip of tape on each side of every flat of the nut holding it all together. Be sure to not put the tape past the flat part of the sheave face in the center or getting it out when you release it will be very difficult.(I know the tape in the pic was past the slope line, but I trimmed it after with a utility knife) Also trim the tape around the back of the spring seat about 1/4” wider than the hole. Once done, remove the nut and bolt from the assembly, the tape will hold it in place. Now you can take your compressed clutch and assemble the unit in proper order, starting with the metal splined spacer or snap ring if you still have that, then the taped assembly, then the plastic spacer washer, the Woodruff key, the fixed sheave, and the washer and the nut and tighten to specs. Once all that is done, you can cut the tape and release the compressed sheave to its normal position. Peel the tape off of everything and make sure no adhesive residue is left on the sheave face, if so, clean off with a cloth with some carb cleaner or goof off. Roll on your belt and you’re back in business. Don’t forget to grease the bushing. Easy peasy. My apologies if someone else has already thought of this and posted it. I did a fair amount of searching and never found any techniques to help solve this issue. I hope this helps other DIY mechanics without a spare set of hands.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-19-2019, 10:53 AM | #2 |
Getting Wild
Join Date: Mar 2018
Posts: 105
|
Re: Secondary clutch compression trick
Nice work! I also struggled with this so I made a tool to get the job done and bought a clutch retainer tool.
Here is where I documented my method: http://www.buggiesgonewild.com/gas-y...made-easy.html I like your method too! And its cheaper than buying the $60 retainer tool. |
12-20-2019, 01:09 PM | #3 |
Getting Wild
Join Date: Dec 2018
Location: Maine 8/ Florida 4
Posts: 129
|
Re: Secondary clutch compression trick
Well, I am a Scotsman, and we are notorious for our frugality, so cheaper is always near the top of the list.
|
12-20-2019, 05:59 PM | #4 | |
Gone Wild
Join Date: Jan 2012
Location: Houston
Posts: 257
|
Re: Secondary clutch compression trick
Quote:
I used a ratchet strap Sent from my iPhone using Tapatalk |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Need primary clutch to secondary clutch distance on a G9 | Gas Yamaha | |||
whats the trick to make stock cc clutch idle | Clone Engine Swaps | |||
secondary clutch | Gas Yamaha | |||
need secondary clutch for 97 cc | Golf Carts and Parts | |||
G16 Secondary clutch | Gas Yamaha |