Sleeving FE290D

bennyt · 08-15-2014, 01:30 AM

2002 DS
I had my block miched today and it was way over 0.020. Has anyone had experience sleeving one of these. Anyone have a good used one?

tpg · 08-15-2014, 04:51 AM

The 350cc engine is I believe .020 bigger than a 290cc. You may be able to use an oversized 350 piston. You would have to check the engine spec #'s to verify.

bennyt · 08-15-2014, 11:39 AM

Thanks for the info. I'll check it out and post results.

BLACK DEATH · 08-15-2014, 09:04 PM

I hope I don't have to do that to mine.
What was your engine doing before the rebuild

bennyt · 08-16-2014, 12:27 AM

I bought this cart for $200.00. It had set up a for a while and after I got it running it smoked like a tar keel.I found a split in the air intake tube and decided to tear it down. Apparently it had been run like this for a long time and the cylinder is worn past the maximum bore. Does anyone know of a cw rotation engine other than the big block clones?

BLACK DEATH · 08-16-2014, 02:35 PM

I don't think there are any cw rotation engines other than cc 290 & 350 ones.
I thought all clones and name brand went ccw rotation

08-15-2014, 01:30 AM	#1
bennyt Not Yet Wild Join Date: Jun 2014 Posts: 13	Sleeving FE290D 2002 DS I had my block miched today and it was way over 0.020. Has anyone had experience sleeving one of these. Anyone have a good used one?
bennyt Not Yet Wild Join Date: Jun 2014 Posts: 13

08-15-2014, 04:51 AM	#2
tpg Gone Wild Join Date: Dec 2007 Location: SE Indiana Posts: 392	Re: Sleeving FE290D The 350cc engine is I believe .020 bigger than a 290cc. You may be able to use an oversized 350 piston. You would have to check the engine spec #'s to verify.

08-15-2014, 11:39 AM	#3
bennyt Not Yet Wild Join Date: Jun 2014 Posts: 13	Re: Sleeving FE290D Thanks for the info. I'll check it out and post results.
bennyt Not Yet Wild Join Date: Jun 2014 Posts: 13

08-15-2014, 09:04 PM	#4
BLACK DEATH Gone Wild Join Date: Dec 2009 Location: Corpus Christi, TX Posts: 1,644	Re: Sleeving FE290D I hope I don't have to do that to mine. What was your engine doing before the rebuild

08-16-2014, 12:27 AM	#5
bennyt Not Yet Wild Join Date: Jun 2014 Posts: 13	Re: Sleeving FE290D I bought this cart for $200.00. It had set up a for a while and after I got it running it smoked like a tar keel.I found a split in the air intake tube and decided to tear it down. Apparently it had been run like this for a long time and the cylinder is worn past the maximum bore. Does anyone know of a cw rotation engine other than the big block clones?
bennyt Not Yet Wild Join Date: Jun 2014 Posts: 13

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

08-16-2014, 02:35 PM	#6
BLACK DEATH Gone Wild Join Date: Dec 2009 Location: Corpus Christi, TX Posts: 1,644	Re: Sleeving FE290D I don't think there are any cw rotation engines other than cc 290 & 350 ones. I thought all clones and name brand went ccw rotation

Similar Threads
Thread	Forum
Pictres of my other girl, 2000 Club Car DS FE290D	Gas Club Car
Concerned about Kawasaki FE290d-CS17	Gas Club Car
In Need of FE290D-DS05 Parts or Complete Engine	Gas Club Car
wires from a 2000 fe290d	Gas Club Car
So I have a KAWASAKI FE290D, in my 87 cart.	Gas Club Car