lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric EZGO
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV.



Post New Thread  Reply
 
Thread Tools Display Modes
Old 09-26-2018, 09:20 PM   #11
Stingray240CS
Getting Wild
 
Join Date: Nov 2017
Posts: 110
Default Re: New install - no reverse

The only place that I can't see that it could be shorting is on the positive and negative posts on the bottom of the reversing contactor. I'm going to make a new negative cable for that too and try again.

Sent from my SM-G965U using Tapatalk
Stingray240CS is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 09-26-2018, 09:21 PM   #12
Stingray240CS
Getting Wild
 
Join Date: Nov 2017
Posts: 110
Default Re: New install - no reverse

It would also be nice to know more about the switch so I knew I was using the correct side of the posts. I thought they might be the same, but they produce different outcomes.

Sent from my SM-G965U using Tapatalk
Stingray240CS is offline   Reply With Quote
Old 09-26-2018, 09:50 PM   #13
Stingray240CS
Getting Wild
 
Join Date: Nov 2017
Posts: 110
Default Re: New install - no reverse

I just created a new ground cable that links the two bottom - terminals on the contactor to the B- on the controller since I wasnt 100% sure there wasnt something touching. The new wire is perfect with nothing exposed. Same issue.

Sent from my SM-G965U using Tapatalk
Stingray240CS is offline   Reply With Quote
Old 09-26-2018, 10:02 PM   #14
Stingray240CS
Getting Wild
 
Join Date: Nov 2017
Posts: 110
Default Re: New install - no reverse

Should these two wires go anywhere? It's the black and red or orange wire that are in the same loom as the green wire.

Sent from my SM-G965U using Tapatalk
Stingray240CS is offline   Reply With Quote
Old 09-27-2018, 08:08 AM   #15
scottyb
Happy Carting
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
Default Re: New install - no reverse

I was looking at this SW202 install again and I think I see 2 high amperage cables on the same terminal. and an empty terminal on the opposite side. Is that what I am seeing? If yes this could be the problem
scottyb is offline   Reply With Quote
Old 09-27-2018, 08:45 AM   #16
Stingray240CS
Getting Wild
 
Join Date: Nov 2017
Posts: 110
Default Re: New install - no reverse

I would say that you are correct Scotty.



Sent from my SM-G965U using Tapatalk
Stingray240CS is offline   Reply With Quote
Old 09-27-2018, 08:47 AM   #17
Stingray240CS
Getting Wild
 
Join Date: Nov 2017
Posts: 110
Default Re: New install - no reverse

Maybe a better view from top here. Nothing on far left lower posts.



Sent from my SM-G965U using Tapatalk
Stingray240CS is offline   Reply With Quote
Old 09-27-2018, 09:17 AM   #18
Stingray240CS
Getting Wild
 
Join Date: Nov 2017
Posts: 110
Default Re: New install - no reverse

I'll have to label my connections so you have a more clear picture. I was trying to use your picture as a guide when I was unclear in the instructions.

I'm guessing my A1 needs to move over to the right post and my B+ needs to move from that bottom right post to the bottom left post that is closest to the top left of the picture.

Hope that makes sense.



Sent from my SM-G965U using Tapatalk
Stingray240CS is offline   Reply With Quote
Old 09-27-2018, 09:25 AM   #19
Stingray240CS
Getting Wild
 
Join Date: Nov 2017
Posts: 110
Default Re: New install - no reverse

Sorry for all the pictures. I notice now that your contactor is slightly different than mine.

Here is mine labeled and with questions on where to move the wires.


Sent from my SM-G965U using Tapatalk
Stingray240CS is offline   Reply With Quote
Old 09-27-2018, 10:22 AM   #20
scottyb
Happy Carting
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
Default Re: New install - no reverse

Yes, move B+ as noted. If a copper bar connect 2 points electrically these bolts are the same point. There should be only one cable per connection point.
scottyb is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric EZGO


Thread Tools
Display Modes


Similar Threads
Thread Forum
new controler install now (forward and reverse are backwards)need help Electric Club Car
Troubleshooting forward/reverse unit install Electric EZGO
EZGO Headlight install - new install not working Electric EZGO
Reverse buzzer install after controller conversion Electric Club Car
Install 6" all sport lift kit trouble install steering linkage Lifted Golf Carts


All times are GMT -5. The time now is 12:12 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.