|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-11-2016, 05:38 PM
|
#12 |
|
Not Yet Wild
Join Date: Sep 2016
Posts: 29
|
Re: Ezgo series wound clicks but won't GO
Got it. Is there a preferred vendor here on these forums? I'd love to support the guys helping me get this thing running again!
|
|
|
|
09-11-2016, 05:50 PM
|
#13 |
|
Not Yet Wild
Join Date: Sep 2016
Posts: 29
|
Re: Ezgo series wound clicks but won't GO
Wait. Didn't see the response on the solenoid replacement. I should just need a new resistor right? Or does the resistor ruin the solenoid (or vice versa)?
|
|
|
|
|
09-11-2016, 07:25 PM
|
#14 |
|
Not Yet Wild
Join Date: Sep 2016
Posts: 29
|
Re: Ezgo series wound clicks but won't GO
Another question for diagnostic purposes, is there a way to test to see if this resistor is going to be the fix? Is jumping the solenoid an option at all or does that take out all functionality of the pedal?
I'm not in a major rush to get running again, but I could save on shipping to order multiple things at once obviously |
|
|
|
|
09-11-2016, 07:31 PM
|
#15 |
|
Guest
Posts: n/a
|
Re: Ezgo series wound clicks but won't GO
the resistor supplys constant power to the controller so it does not get a spark
i do not know if it is bad that it won't make cart run |
|
|
|
09-11-2016, 07:36 PM
|
#16 |
|
Not Yet Wild
Join Date: Sep 2016
Posts: 29
|
Re: Ezgo series wound clicks but won't GO
So by limiting too much voltage and only pre loading the controller with 28v, the controller is not kicking on because it thinks the batteries are discharged? Or does it have a safety feature kick in to keep it from arcing?
Obviously I'm ordering a new resistor, just trying to wrap my brain around what it does. I've got a couple shops here within 5 minutes of my house that may keep this resistor on hand. Was hoping to order online at a site vendor, but that may have to wait until next year... Planning to upgrade the controller etc to get some more balls out of this thing! |
|
|
|
|
09-11-2016, 07:39 PM
|
#17 |
|
Guest
Posts: n/a
|
Re: Ezgo series wound clicks but won't GO
i think that is correct ... hopefully scotty will chime in
|
|
|
|
09-11-2016, 08:23 PM
|
#18 |
|
Not Yet Wild
Join Date: Sep 2016
Posts: 29
|
Re: Ezgo series wound clicks but won't GO
Another odd one... When I test the resistor with the multimeter, it shows exactly 250 which is what it's rated for! I assumed the resistor would read low showing the same results I got in voltage when it was installed. Seems odd that it would neck down the voltage by 25%+ and still read at its rating of 250ohms
|
|
|
|
|
09-11-2016, 08:35 PM
|
#19 |
|
Guest
Posts: n/a
|
Re: Ezgo series wound clicks but won't GO
maybe it's the rats !!!
  |
|
|
|
09-11-2016, 09:34 PM
|
#20 |
|
Gone Wild
Join Date: May 2015
Location: Central Florida
Posts: 2,114
|
Re: Ezgo series wound clicks but won't GO
bad resistor is not your problem
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| EZGO Series TXT clicks but won't go | Electric EZGO | |||
| Club Car Series Controller + EZGO Series Wound Motor | Electric Club Car | |||
| retrofit '86 series-wound motor from resistor-controller to...? | Electric EZGO | |||
| EZGO series cart won't go but clicks | Electric EZGO | |||
| EZ-go Marathon series or shunt wound motor? | Electric EZGO | |||
Linear Mode
