|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
07-26-2018, 05:47 AM | #1 |
Gone Wild
Join Date: Oct 2008
Location: East Texas
Posts: 586
|
Series Cart No Go
A buddy of mine called me yesterday and said his cart all of a sudden won't run. It's a 36 volt ezgo series cart. I went over to check it out. The batteries are 2 years old and measure at 38.4 volts. Turn the key on, put if reverse, buzzer comes on, hit the gas and the solenoid clicks but no movement. I checked voltage on the solenoid and the F/R switch and have pack voltage. I checked all of the cables and all are clean and tight. Suggestions?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-26-2018, 01:00 PM | #2 |
Not Yet Wild
Join Date: Jul 2017
Location: salem ohio
Posts: 29
|
Re: Series Cart No Go
just a thought but did you ck the reed in the charger unit that is attached to the body ? just found out that if they go out theres no click on solenoid. just bypass it .
|
07-27-2018, 08:32 AM | #3 |
Not Yet Wild
Join Date: Jul 2018
Posts: 8
|
Re: Series Cart No Go
where is the reed for the charger located at on the body? I have the exact same thing he has...a no go issue...
Edit: Are you referring to the actual charging port? I am new to all this and the lingo... if sop, How do you do the bypass loop thing? Last edited by ironcwb; 07-27-2018 at 08:36 AM.. Reason: Verification |
07-27-2018, 08:58 AM | #4 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Series Cart No Go
The reed switch is inside the charge receptacle. If the solenoid is clicking as the OP stated then the reed switch is working and I suspect the F&R high amperage contacts are compromised.
|
07-28-2018, 09:15 AM | #5 |
Not Yet Wild
Join Date: Jul 2018
Posts: 8
|
Re: Series Cart No Go
So, I have no reason to bypass the reed switch if solenoid is clicking? But mine only clicks in reverse. I have a brand spanking new F/R thing in there... complete set up, just bolted in. So , I am guessing it is good since it is new. I am new to all this as well
|
07-28-2018, 03:16 PM | #6 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Series Cart No Go
In an Ezgo Series cart like this one the same micro switch on the F&R is triggered in both forward and reverse. This is true for the Marathon and the TXT models. In the TXT this is the switch on the drivers side. This switch sends power to the key switch which sends power to the pedal box switch which sends power to the solenoid coil and BOOM it clicks.
If this micro switch only clicks in one direction look closely at the switch trigger. That's the little arm with the roller. It should be going into a detent in cam in both F&R position. Sometimes the arm is bent or the F&R is not installed correctly and the shift linkage prevents the cam from reaching it's full rotation. To adjust the cam rotation, loosen the 2 floor mount bolts and slide the F&R east or west on the floor to allow proper linkage travel when shifting. To avoid this problem when replacing an F&R in the TXT Always mark the F&R position on the floor before removing it. See my instruction attached. I hope this helps |
07-30-2018, 06:41 AM | #7 |
Gone Wild
Join Date: Oct 2008
Location: East Texas
Posts: 586
|
Re: Series Cart No Go
Scotty, if I have pack voltage on the F/R switch could it still be the issue?
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Interchangability of parts EZGO Medalist series cart and TXT series | Electric EZGO | |||
Will a 95 series motor and controller fit in a 94 series cart? | Electric EZGO | |||
New TXT Series cart | Electric EZGO | |||
How compatible would a DCS cart be with a newer Series cart? | Electric EZGO | |||
Upgrading cart from EZGO Series cart | Electric EZGO |