|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
10-17-2019, 08:04 AM | #1 |
Not Yet Wild
Join Date: Jun 2019
Posts: 63
|
Alltrax error code
So, Ive got my cart all back together running a allttrax. I was having a problem getting the unit to power up, well, thats fixed. I replaced the foot pedal microswitch as per scottbs' suggestion and now I have an error message ..I'm getting 2 green with 6 red blips which tells me that I have" Low Throttle Under range",
What does that mean? How do I fix it? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-17-2019, 08:39 AM | #2 |
Gone Wild
Join Date: Jul 2010
Location: Peachtree City, Ga.
Posts: 2,759
|
Re: Alltrax error code
From the Alltrax web site:
Note 2: Low Throttle range is the pedal “at rest OFF pedal position” The throttle could be faulty Wiring/connectors Incorrect throttle set in the program Otherwise, Clear throttle auto-calibration and try again I would try the last one first. |
10-17-2019, 08:59 AM | #3 | |
Not Yet Wild
Join Date: Jun 2019
Posts: 63
|
Re: Alltrax error code
Quote:
|
|
10-17-2019, 09:29 AM | #4 |
Gone Wild
Join Date: Jul 2010
Location: Peachtree City, Ga.
Posts: 2,759
|
Re: Alltrax error code
You need the Alltrax tool kit software (free download) on a PC and a USB printer cable to connect to the controller.
The error is suggesting the signal is not correct from the go peddle when it is in the full up position. Confirm at power up the controller gives 4 green flashes indicating it is set for the ITS throttle. Coming from Scottyb this should be correct but check anyway. Since you got this from CU it's probably best to contact them for installation issues. |
10-17-2019, 09:45 AM | #5 |
Not Yet Wild
Join Date: Jun 2019
Posts: 63
|
Re: Alltrax error code
Thanks for your advice. shoudda mentioned, I do get the 4 green blips b4 the error and the error is when the pedal is fully depressed. Does that change anything?
|
10-17-2019, 10:38 AM | #6 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Alltrax error code
Doing the auto-cal is treating the symptoms rather than solving the problem.
Measure the voltage between the black and white wires going to the ITS sensor. Should be 10V when pedal is pushed just far enough to make solenoid click and 6V when pedal is on floor. Thee most likely culprit is the 4-pin in-line connector that connects the gray cable from the pedal box to the four wires going to controller, solenoid and wiring harness. Replace it with individual butt splices or soldered connections. |
10-17-2019, 12:46 PM | #7 | |
Not Yet Wild
Join Date: Jun 2019
Posts: 63
|
Re: Alltrax error code
Quote:
|
|
10-17-2019, 01:42 PM | #8 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Alltrax error code
Connect the black wire from the solenoid's small terminal on the bottom in the picture, to the B- terminal on the controller. That is needed to complete the solenoid activation circuit.
|
10-17-2019, 02:06 PM | #9 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: Alltrax error code
It looks like he is using the Controller provided SOL- for the coil negative activation.
Isn't there a wire missing from the FNR limit switch? |
10-17-2019, 02:53 PM | #10 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Alltrax error code
Quote:
Yep, there does appear to be a missing wire on the upper microswitch. The green wire with the wirenut on it should be connected to there. |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
ALLTRAX XCT500 36v Battery Under Voltage error code | Electric EZGO | |||
New ALLTRAX XTC 48500 PDS controller Error code | Electric EZGO | |||
Alltrax XTC 500 Error Code | Electric EZGO | |||
06 TXT PDS 36v- Alltrax error code question | Electric EZGO | |||
Alltrax SPM 48500 error code | Electric EZGO |