e z go elec died on the course

rjc97 · 07-24-2010, 10:26 PM

Amazing!!!! I'm sure there have been changes since this configeration was installed.

Will keep at it and keep you posted...Thanks for the info...

scottyb · 07-24-2010, 10:36 PM

I want you to check 1 little thing..... put the test leads on the 2 small solenoid terminals. key on, in gear, push the gas = any voltage reading?

scottyb · 07-24-2010, 10:40 PM

NO voltage? Install a jumper on the large posts of the solenoid. Does it run?

rjc97 · 07-24-2010, 11:01 PM

Will Give it another try....

Thanks for the reply

rjc97 · 07-25-2010, 04:57 PM

ok Test Probes on small terminals of solenoid resulted in voltage of 37.3....

Jumper wire on large terms....no go....

????

rabbitreborn · 07-25-2010, 05:05 PM

Hang on there.... we're in for a bumpy ride.....

are you getting the solenoid to click?

If so, are you getting power on the controller side of the solenoid with the cart in gear, key on and pedal down?

Does your controller still have the white connector that plugs into the 5 pins on the top of the controller?

rjc97 · 07-25-2010, 05:23 PM

Yes on all accounts

solenoid clicks
Key on Gear Forward pedal down

White connector to the 5 pin on top of the controller

rjc97 · 07-27-2010, 10:21 PM

Hello Again...Hopefully the mystery to the E Z Go has been solved....After replacing the
speed controller, solenoid, micro switch in acellerator box, new harness to the solenoid, and a lot of frustration and phone calls to different Techs.....While probing the 6 pin connector with volt meter....It has been determined there were two wires not making contact.....We now have motor activation and wheels turning.....We should be putting the pieces back together tomorrow and getting this cart back on the course....Thanks to all who replied with suggestions...

scottyb · 07-28-2010, 08:59 AM

OUCH...... sounds like an hour of tech shop time would have been a lot cheaper than all those parts ..... that pin connector can get loose if you drive rm in the rough a lot

Glad to hear you got her going and thank you for completing this thread so it can help somebody in the future with a similar problem

07-24-2010, 10:26 PM	#21
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36	Re: e z go elec died on the course Amazing!!!! I'm sure there have been changes since this configeration was installed. Will keep at it and keep you posted...Thanks for the info...
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36

07-24-2010, 10:36 PM	#22
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,406	Re: e z go elec died on the course I want you to check 1 little thing..... put the test leads on the 2 small solenoid terminals. key on, in gear, push the gas = any voltage reading?

07-24-2010, 10:40 PM	#23
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,406	Re: e z go elec died on the course NO voltage? Install a jumper on the large posts of the solenoid. Does it run?

07-24-2010, 11:01 PM	#24
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36	Re: e z go elec died on the course Will Give it another try.... Thanks for the reply
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36

07-25-2010, 04:57 PM	#25
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36	Re: e z go elec died on the course ok Test Probes on small terminals of solenoid resulted in voltage of 37.3.... Jumper wire on large terms....no go.... ????
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

07-25-2010, 05:05 PM	#26
rabbitreborn Gone Wild Join Date: Jun 2010 Location: Central Florida Posts: 2,757	Re: e z go elec died on the course Hang on there.... we're in for a bumpy ride..... are you getting the solenoid to click? If so, are you getting power on the controller side of the solenoid with the cart in gear, key on and pedal down? Does your controller still have the white connector that plugs into the 5 pins on the top of the controller?

07-25-2010, 05:23 PM	#27
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36	Re: e z go elec died on the course Yes on all accounts solenoid clicks Key on Gear Forward pedal down White connector to the 5 pin on top of the controller
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36

07-27-2010, 10:21 PM	#28
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36	Re: e z go elec died on the course Hello Again...Hopefully the mystery to the E Z Go has been solved....After replacing the speed controller, solenoid, micro switch in acellerator box, new harness to the solenoid, and a lot of frustration and phone calls to different Techs.....While probing the 6 pin connector with volt meter....It has been determined there were two wires not making contact.....We now have motor activation and wheels turning.....We should be putting the pieces back together tomorrow and getting this cart back on the course....Thanks to all who replied with suggestions...
rjc97 Not Yet Wild Join Date: Mar 2009 Posts: 36

07-28-2010, 08:59 AM	#29
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,406	Re: e z go elec died on the course OUCH...... sounds like an hour of tech shop time would have been a lot cheaper than all those parts ..... that pin connector can get loose if you drive rm in the rough a lot Glad to hear you got her going and thank you for completing this thread so it can help somebody in the future with a similar problem

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
'85 Club Car Died	Electric Club Car
just died on me.	Gas EZGO
new cart died help	Electric Club Car
cart just died	Electric EZGO
02 Ez Go Electric Died	Electric EZGO