|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
06-02-2013, 08:09 PM
|
#1 |
|
Not Yet Wild
Join Date: May 2013
Posts: 21
|
all new parts still no spark !
OK still NO SPARK !!!
Ok here's where i'm at now. Changed the plug and plug wire. Changed the coil out with a new auto coil. No difference. Changed the igniter out with a new auto one and followed steps for rewiring. Still no spark. Tried switching the 2 pulsar wires like was mentioned. Still no spark. Tried reversing the polarity cause I saw something about this being an issue with not starting. Still nothing !! I checked an rechecked all my wiring and connections and the coil and igniter are mounted just in case there is a ground issue. I'm kinda at a loss now. Any ideas where to go from here ??? Thank you in advance. |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-03-2013, 07:22 AM
|
#2 |
|
Gone Wild
 Join Date: Mar 2012
Location: CENTRAL PENNSYLVANIA
Posts: 1,466
|
Re: all new parts still no spark !
ok first what are we working on ? make model 2 or 4 stroke?
|
|
|
|
|
06-03-2013, 08:17 AM
|
#3 |
|
Not Yet Wild
Join Date: May 2013
Posts: 21
|
Re: all new parts still no spark !
1986 GXT 800 2 stroke EZGo. After changing the plug and then plug wire with no luck I did the HEI conversion that was posted by Ron Man using all new parts.
Still no spark. I checked and rechecked all connections and wiring. Getting very frustrated with this thing. Any ideas ?>? |
|
|
|
|
06-03-2013, 10:01 AM
|
#4 |
|
Gone Wild
Join Date: Apr 2011
Location: Washington State
Posts: 385
|
Re: all new parts still no spark !
Some checks you can do. Verify you have a solid +12V on the pos+ of your coil when cranking, also +12v on the hei terminal.(2) verify you have the hei bottom plate grounded good.(3) Unplug your pulsar connector, measure ohms of the two wires going into motor blower houssing and report back. also measure each pin to ground. 3) set your meter to ac volts, lowest voltage setting, connect leads to pulsar wires, crank motor, reading should be .3 to .5 volts ac or greater.
|
|
|
|
|
06-03-2013, 03:19 PM
|
#5 |
|
Getting Wild
Join Date: Apr 2013
Location: N.E. Louisiana
Posts: 78
|
Re: all new parts still no spark !
Check your Ignition Switch & Wires
|
|
|
|
|
06-03-2013, 06:57 PM
|
#6 |
|
Not Yet Wild
Join Date: May 2013
Posts: 21
|
Re: all new parts still no spark !
ok got a spark ! ended up being a missing ground thanks for every ones help
|
|
|
|
|
06-03-2013, 09:46 PM
|
#7 |
|
Gone Wild
Join Date: Apr 2013
Location: Morgan Hill, California
Posts: 207
|
Re: all new parts still no spark !
</golf clap>
Well done men... |
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| 1980 ezgo gas SPARK/NO SPARK | Gas EZGO | |||
| 1994 club car no spark / then spark | Gas Club Car | |||
| had spark, pulled engine, now no spark | Gas EZGO | |||
| 88 marathon new 79 dodge coil little spark then no spark? | Gas EZGO | |||
| new parts still no spark | Gas Club Car | |||
Linear Mode
