|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
08-04-2007, 03:35 PM
|
#11 |
|
Gone Wild
Join Date: Dec 2006
Location: ComplainAboutNoNo'sProfile-Ville
Posts: 4,995
|
Re: Yamaha governor bypass
You will probably have to put a little more cable towards the pedal with the adjustment end of the cable. I did this same mod today and had good results. I also put a jet and a K&N in the carb. It runs great but acts like it wants to bog when you get on it. Probably a fuel and air mixture problem.
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
08-04-2007, 07:32 PM
|
#12 |
|
Gone Wild
Join Date: Jan 2007
Location: Anchorage AK
Posts: 181
|
Re: Yamaha governor bypass
I have no bog or hesitation, it will not go at slow speeds the switch will click. How do you make it key start? Same as the EZ-GO?
|
|
|
|
08-04-2007, 07:54 PM
|
#13 |
|
Gone Wild
Join Date: Dec 2006
Location: ComplainAboutNoNo'sProfile-Ville
Posts: 4,995
|
Re: Yamaha governor bypass
Move the threaded end of the cable towards the front of the cart. If I remember correctly, they're 10mm nuts. I have no idea how to make an E-Z-GO key start. Even less on a Yamaha. I can do it on a Club Car, but that's it.
|
|
|
|
08-05-2007, 10:29 AM
|
#14 |
|
WILD
Join Date: May 2007
Location: lebanon county,pa
Posts: 1,266
|
Re: Yamaha governor bypass
you might be able to just jump the micro switch for the pedal this should just let the engine running whenever the key is on but a better carts clutch might just engage right away?
|
|
|
|
08-05-2007, 10:30 AM
|
#15 |
|
Gone Wild
Join Date: Dec 2006
Location: ComplainAboutNoNo'sProfile-Ville
Posts: 4,995
|
Re: Yamaha governor bypass
Ask that again in the form of a question.
 Yamaha clutches engage as soon as they're spun since they have no stall spring in them. |
|
|
|
08-05-2007, 11:11 AM
|
#16 |
|
WILD
Join Date: May 2007
Location: lebanon county,pa
Posts: 1,266
|
Re: Yamaha governor bypass
ok then my ezgo had a really worn clutch i would be able to hit the gas about 2 inches untill it started to move
|
|
|
|
08-21-2007, 02:45 PM
|
#17 |
|
Gone Wild
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,882
|
Re: Yamaha governor bypass
a picture of the two cables connected together
 |
|
|
|
08-26-2007, 08:44 PM
|
#18 |
|
Not Yet Wild
Join Date: Aug 2007
Location: Central Point, Oregon
Posts: 20
|
Re: Yamaha governor bypass
I have just done this to my G9 and wow what a difference. Thanks a ton for the play by play with the pics, it was a big help!
|
|
|
|
08-26-2007, 10:02 PM
|
#19 |
|
Gone Wild
Join Date: Aug 2007
Location: Yukon, OK
Posts: 234
|
Re: Yamaha governor bypass
For the G16 to "idle" take out the pedal inspection cover and look behind the gas pedal. Flip the Micro upside down and the cart will "idle".
|
|
|
|
11-11-2007, 12:13 PM
|
#20 |
|
The Overposter!
Join Date: Nov 2007
Location: Dixie
Posts: 1,586
|
Re: Yamaha governor bypass
hmmmmm, i didnt have to do any of that on my g2 back when it was stock...
see the cable that hooks to the carb, its L shaped, just straighten the joint out and tighten the screw on it and wala, it bypasses it. then if you want it slow again just loosen the screw.... |
|
|
Linear Mode
