|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
10-26-2019, 01:36 PM
|
#1 |
|
Getting Wild
Join Date: Oct 2010
Location: Tavares, Florida
Posts: 121
|
96 TXT Won't Move
I have a 96 TXT with an SPM48500 and SW202 reverse contactors that won't move. Controller is flashing two green and three red, hook up laptop with Alltrax and the monitor shows high throttle voltage when depressing the pedal (doesn't matter how far). Should I be replacing the ITS or is there somewhere else to look first? Reverse contactor is functioning fine as is the solenoid for the controller.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
10-26-2019, 05:31 PM
|
#2 |
|
Techno-Nerd
 Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 96 TXT Won't Move
If it hasn't already be done, cut off the 4-pin in-line connector the joins the gray cable from the pedal box to the cart wring harness and install individual butt splices or solder joints and cover with marine grade (waterproof) shrink tubing.
Cross-talk between pins often occurs when that connector gets damp or corroded. The throttle signal (voltage between black and white wires to ITS sensor) should be 10V when pedal is pushed just far enough to make solenoid click and should decrease to 6V when pedal pushed to floor. |
|
|
|
|
10-26-2019, 08:11 PM
|
#3 |
|
Getting Wild
Join Date: Oct 2010
Location: Tavares, Florida
Posts: 121
|
Re: 96 TXT Won't Move
It's been done but not to that extent. I plan on going through the wiring anyway because things are a mess but I'm kicking myself for having my DMM at work.
|
|
|
|
|
10-28-2019, 03:35 PM
|
#4 |
|
Getting Wild
Join Date: Oct 2010
Location: Tavares, Florida
Posts: 121
|
Re: 96 TXT Won't Move
Voltage across those pins is going from 8.88 to 6.66 at full depression.
|
|
|
|
|
10-28-2019, 03:37 PM
|
#5 |
|
Getting Wild
Join Date: Oct 2010
Location: Tavares, Florida
Posts: 121
|
Re: 96 TXT Won't Move
Ha, just wiggled the factory 4 pin connector and got my gears back. Thanks Johnnie.
|
|
|
|
|
10-29-2019, 05:24 PM
|
#6 |
|
Getting Wild
Join Date: Oct 2010
Location: Tavares, Florida
Posts: 121
|
Re: 96 TXT Won't Move
Yeah, well, scratch that. Full throttle it drops all power unless you left off a bit. Going to chop the factory harness and convert to spades. Could the ITS still be bad with the voltages I read yesterday?
|
|
|
|
|
10-29-2019, 07:04 PM
|
#7 |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 96 TXT Won't Move
Wait until the in-line connector has been eliminated and the four wires are completely separated from each other, then check the pedal up / pedal down voltages.
|
|
|
|
|
10-30-2019, 04:56 PM
|
#8 |
|
Getting Wild
Join Date: Oct 2010
Location: Tavares, Florida
Posts: 121
|
Re: 96 TXT Won't Move
Okay, factory connector bypassed. Showing 8.77v at slight depression and 6.84v at full depression.
|
|
|
|
|
10-30-2019, 06:47 PM
|
#9 |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 96 TXT Won't Move
Are you still getting the 2-grn/3-red error code?
If so, it is time to look at the ITS sensor. |
|
|
|
|
10-30-2019, 06:48 PM
|
#10 |
|
Getting Wild
Join Date: Oct 2010
Location: Tavares, Florida
Posts: 121
|
Re: 96 TXT Won't Move
Actually, it switched up. Two green and five red. It went from "high throttle range" to "low throttle range". Still the ITS I assume?
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| G16 won't move | Gas Yamaha | |||
| 99 TXT won't move | Electric EZGO | |||
| 1996 Series DS 48V won't move on ground, wheels barely move on jacks | Electric Club Car | |||
| 99 ez go won't move | Electric EZGO | |||
| will not move | Electric EZGO | |||
Linear Mode
