Charging connection

djhartley2003 · 09-22-2010, 01:54 PM

I need a little help. I looked on a couple of the sponsor's sites and I am sure I am just not searching it right but I need some help finding the battery charging connection on the cart side for my 36 volt 1994 ezgo marathon. Or i might not be seeing how it goes together. It is supposed to snap into place and hold it down. I have is the battery connection and the piece that looks like a bezel but I cant figure out how it goes together to hold it in place. Can any one tell me how this goes together or if I need a new one. If I need a new one what exactly do I need and where do I get it? Thanks a lot for any help.
these 2 are shots of the cart
P9180312.jpg

P9180313.jpg

this is the bezel
receptacle bezel.jpg

this is on the charger side
charger side.jpg

mauistardog · 09-22-2010, 02:20 PM

Yes you have a SB50. The only part you are missing is a screw..no offense intended. :-) A screw from the side of the bezel trim that goes on the cart will hold the connection on the cart in place in the bezel. the bezel should snap on to the body of the cart, some have screws but I think that marathon model snaps with some tabs. You can search for SB50 connections on part sites.

aloha
joe

djhartley2003 · 09-22-2010, 02:54 PM

Thank you for the help. No offense taken. My wife tells me all the time I have a screw loose so its OK to find out that I need a new one.

COURTESYCART · 09-23-2010, 08:40 AM

if you are replacing those charger ends, now IMO would be a good time to upgrade. That charger ends are known to give issues. I have actuatly had them melt so bad the charger harness melted to the cart while charging.

I would upgrade to the 2 prong connection or the txt version. they have a better connection.

But yes as stated the cart end is held in the bezel by a screw

djhartley2003 · 09-23-2010, 03:18 PM

Are the ends interchangeable to the different types of carts?

COURTESYCART · 09-23-2010, 04:10 PM

Quote:

Originally Posted by djhartley2003

Are the ends interchangeable to the different types of carts?

If you get the male and female matching ends.

djhartley2003 · 09-24-2010, 10:50 PM

so as long as the male and female ends match the rest of it doesn't mater (motor, controller or any of the other parts).

09-22-2010, 01:54 PM	#1
djhartley2003 Gone Wild Join Date: Apr 2009 Location: Chino Ca Posts: 209	Charging connection I need a little help. I looked on a couple of the sponsor's sites and I am sure I am just not searching it right but I need some help finding the battery charging connection on the cart side for my 36 volt 1994 ezgo marathon. Or i might not be seeing how it goes together. It is supposed to snap into place and hold it down. I have is the battery connection and the piece that looks like a bezel but I cant figure out how it goes together to hold it in place. Can any one tell me how this goes together or if I need a new one. If I need a new one what exactly do I need and where do I get it? Thanks a lot for any help. these 2 are shots of the cart P9180312.jpg P9180313.jpg this is the bezel receptacle bezel.jpg this is on the charger side charger side.jpg

09-22-2010, 02:20 PM	#2
mauistardog Gone Wild Join Date: Dec 2009 Location: Waihee, Maui, Hawaii Posts: 262	Re: Charging connection Yes you have a SB50. The only part you are missing is a screw..no offense intended. :-) A screw from the side of the bezel trim that goes on the cart will hold the connection on the cart in place in the bezel. the bezel should snap on to the body of the cart, some have screws but I think that marathon model snaps with some tabs. You can search for SB50 connections on part sites. aloha joe

09-22-2010, 02:54 PM	#3
djhartley2003 Gone Wild Join Date: Apr 2009 Location: Chino Ca Posts: 209	Re: Charging connection Thank you for the help. No offense taken. My wife tells me all the time I have a screw loose so its OK to find out that I need a new one.

09-23-2010, 08:40 AM	#4
COURTESYCART Gone Wild Join Date: Nov 2008 Location: Montgomery, AL Posts: 1,463	Re: Charging connection if you are replacing those charger ends, now IMO would be a good time to upgrade. That charger ends are known to give issues. I have actuatly had them melt so bad the charger harness melted to the cart while charging. I would upgrade to the 2 prong connection or the txt version. they have a better connection. But yes as stated the cart end is held in the bezel by a screw

09-23-2010, 03:18 PM	#5
djhartley2003 Gone Wild Join Date: Apr 2009 Location: Chino Ca Posts: 209	Re: Charging connection Are the ends interchangeable to the different types of carts?

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

09-24-2010, 10:50 PM	#7
djhartley2003 Gone Wild Join Date: Apr 2009 Location: Chino Ca Posts: 209	Re: Charging connection so as long as the male and female ends match the rest of it doesn't mater (motor, controller or any of the other parts).

Similar Threads
Thread	Forum
Need Help W/ Connection to Igniter	Gas Yamaha
G1 Charger Connection	Electric Yamaha
G16 losing connection	Gas Yamaha
A2 connection	Electric Club Car
A1 connection	Electric EZGO