12-18-2016, 06:09 PM | #21 |
Not Yet Wild
Join Date: Dec 2016
Posts: 30
|
Re: FE 290 carb
what causes the float to get full of gas
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-18-2016, 06:10 PM | #22 |
Gone Wild
Join Date: Mar 2012
Location: Baton Rouge, La.
Posts: 398
|
Re: FE 290 carb
|
12-18-2016, 06:20 PM | #23 |
Not Yet Wild
Join Date: Dec 2016
Posts: 30
|
Re: FE 290 carb
and this would cause gas to come out the overflow hose
|
12-18-2016, 06:22 PM | #24 |
Gone Wild
Join Date: Mar 2012
Location: Baton Rouge, La.
Posts: 398
|
Re: FE 290 carb
|
12-18-2016, 06:28 PM | #25 |
Not Yet Wild
Join Date: Dec 2016
Posts: 30
|
Re: FE 290 carb
Thank everybody for the help
|
12-18-2016, 07:09 PM | #26 |
Not Yet Wild
Join Date: Dec 2016
Posts: 30
|
Re: FE 290 carb
here are a few pics of the float upside down and right side up.Can you tell if the float is to high or to low.I shook the float and no fuel inside
|
12-18-2016, 08:41 PM | #27 |
Gone Wild
Join Date: Mar 2012
Location: Baton Rouge, La.
Posts: 398
|
Re: FE 290 carb
I don't have specific info on that carb, but generally, with the carb held upside down the float should be paralell to the bowl mounting surface. Carefully remove the pin holding the float and needle on and clean the gas passages with spray carb cleaner; there is usually trash keeping the needle valve from shuttiing off gas flow..You do have an inline filter before the carb, right?
|
12-18-2016, 08:49 PM | #28 |
Not Yet Wild
Join Date: Dec 2016
Posts: 30
|
Re: FE 290 carb
yes,I have a inline filter.The carb is a keihin BBKL
|
12-18-2016, 09:45 PM | #29 |
Gone Wild
Join Date: May 2015
Location: Central Florida
Posts: 2,114
|
Re: FE 290 carb
The floats not right. No way its closing.
|
12-18-2016, 10:08 PM | #30 |
Gone Wild
Join Date: Mar 2012
Location: Baton Rouge, La.
Posts: 398
|
Re: FE 290 carb
Looking again, I think it could not open because of the angle. It looks like the float was removed and the needle valve was not installed in the slot on the float properly. WYT? You can buy a new carb on ebay for about $20, I did, but scared to install it after reading somewhere that either the screws come out or the bufferfly breaks causeing a busted piston, so it just sits in the box in my shop. It has Kein markings but im sure it is a china clone.. |
|
|
Similar Threads | ||||
Thread | Forum | |||
carb tuning mikuni or eBay CV carb | Clone Engine Swaps | |||
1989 Ezgo New Carb leaking gas like the old Carb | Gas EZGO | |||
clone carb vs honda carb | Clone Engine Swaps | |||
cheap carb swap onto 3PG engine- Tecumseh carb works great- with lots of pics | Gas EZGO | |||
91 2 Cycle Carb Missing Carb Screw | Gas EZGO |