05-06-2011, 05:59 PM | #1 |
Not Yet Wild
Join Date: May 2011
Location: Summerfield NC
Posts: 4
|
Eh29
Hey I'm new to the board an have been reading it alot. I need some help on a eh 29 motor. Did a compression test on the cylinders one is 120 and the other is 0 can some tell what may be wrong.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-06-2011, 06:04 PM | #2 |
Respect the Cart
Join Date: May 2010
Location: Rocky Mount, Virginia
Posts: 2,190
|
Re: Eh29
Zero is pretty serious. You either have a hole in the piston or a burnt out exhaust valve or a stuck open valve. I would remove the valve cover and see if a valve is jammed open. However I fear that you have a seriously distressed engine.
|
05-06-2011, 06:12 PM | #3 |
Getting Wild
Join Date: Feb 2011
Location: Boonville Indiana
Posts: 109
|
Re: Eh29
I agree with Dave, I have the eh29 in my 93 compression on both cylinders runs about 150. you'll just have to tear into it . How long did it set before you got it?
|
05-06-2011, 06:18 PM | #4 |
Not Yet Wild
Join Date: May 2011
Location: Summerfield NC
Posts: 4
|
Re: Eh29
Use it at the lake set over the winter thanks for the help
|
05-06-2011, 08:17 PM | #5 |
Gone Crazy
Join Date: Jan 2007
Location: Chesterfield, Va
Posts: 6,021
|
Re: Eh29
I think you have a stuck open valve, pull the cover and peek at it.
Might just need a tap with a small hammer. |
05-07-2011, 05:53 PM | #6 |
nimda
Join Date: Jun 2007
Posts: 13,022
|
Re: Eh29
The valves are notorious for wearing to the point you have no adjustment left on the rocker. They will literally come completely through the seat. It could be a hole in a piston, burnt valve or even out of adjustment.(not closing) If you loosen the adjusters all the way off and still get no clearance between rocker then new valves are in order. Adjustment info in the stickies.
|
05-09-2011, 02:29 PM | #7 |
Gone Wild
Join Date: Nov 2009
Location: Illinois
Posts: 171
|
Re: Eh29
Are you sure that the piston in the dead cylinder is moving? Could be it threw a rod on that cylinder and the piston is stuck up out of the way enough for the motor to run. I have a 295 parts motor that has a piston that is stuck just like that and it turns freely by hand with no interference from the broken rod.
|
05-09-2011, 02:45 PM | #8 |
Gone Wild
Join Date: Nov 2008
Location: Montgomery, AL
Posts: 1,463
|
Re: Eh29
I have seen several engines comes thru with a broke rod and believe it or no they are quiet, the complaint is "My cart has no power".
Remove the spark plugs, rotate engine over while looking down thru plug hole in cyl with no compression. see if you see the piston moving. if not than you have a broken rod. |
|
|
Similar Threads | ||||
Thread | Forum | |||
High Performance EH29 - EH35 ezgo cam camshaft | Gas EZGO | |||
EH29 or E35 Engine Size | Gas EZGO | |||
EZGO EH29 -EH35 Cam Timing Belt | Ezgo Gas Tech | |||
GM HEI for 4 stroke Robin EH29 | Gas EZGO | |||
robin eh29 info | Gas EZGO |