|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
05-26-2016, 07:41 AM | #11 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: G29 Controller Update
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-26-2016, 12:22 PM | #12 |
Gone Wild
Join Date: Jun 2012
Location: Eagle, WI
Posts: 317
|
Re: G29 Controller Update
So if I decide to add the Alltrax XCT 300 or 400 amp, that I will need to change out my brushes? Haven't heard that one.
|
05-26-2016, 06:33 PM | #13 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: G29 Controller Update
Not alway's. Just found when I installed the last controller it wasn't reaching 22 mph. Through the lap top and help from tech support, the motor was drawing way to many amps. Changed out the update brush rig/brush kit and instantly cured the problem.
|
05-26-2016, 07:44 PM | #14 |
Gone Wild
Join Date: May 2012
Location: Rio Verde, Az
Posts: 7,167
|
Re: G29 Controller Update
Bad brushes can really overheat your motor and it's much worse with more amps from the controller.
|
05-27-2016, 06:14 PM | #15 |
Not Yet Wild
Join Date: Apr 2016
Posts: 34
|
Re: G29 Controller Update
How tough were they to change out
|
05-27-2016, 06:53 PM | #16 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G29 Controller Update
they are among the easiest. no press needed, no snap ring pliers. only "special tool" is a long screw to grab & lift the bearing retainer ring to put the original screws back in.
|
05-28-2016, 09:05 AM | #17 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: G29 Controller Update
About the worst thing is lifting that heavy thing
|
05-28-2016, 12:55 PM | #18 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G29 Controller Update
|
06-30-2016, 04:46 PM | #19 |
Not Yet Wild
Join Date: Jun 2016
Location: Cave Springs, Arkansas
Posts: 17
|
Re: G29 Controller Update
How many sets of brushes would I need to order if I'd like to change them? My YDRE 2012 is only getting 15mph after the fastest setting was uploaded to my controller. Was hoping for the 19.
|
06-30-2016, 06:00 PM | #20 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: G29 Controller Update
Actually, your car is right in the serial number/ date for this brush rig update. It is a new style brush rig/springs/brushes/ and all the screws/insulators....everything. Part # JC1-H7104-09-00 Suggested retail $ 94.15 Good luck
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
1994 36 volt controller CC won't go / update | Electric Club Car | |||
1984 G1-EM4 Controller update | Electric Yamaha | |||
controller update | Columbia ParCar | |||
Update | Electric Club Car |