|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
05-10-2016, 06:27 AM | #1 |
Not Yet Wild
Join Date: Apr 2016
Posts: 37
|
ez go wont run
i have 1996 series cart when i push the pedal the solenoid clicks. on the battery i show 37.3 they are new batteries. on one side of solenoid it shows the same on other side it shows 36.3. it also has new f/r switch and key switch. it has an alltrax controller npx 4844 with the heavier battery cables. dont know where to go next
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-10-2016, 08:46 AM | #2 |
Master of All Things
Join Date: May 2013
Location: West Columbia, Texas
Posts: 17,980
|
Re: ez go wont run
Mark....hopefully you have a digital volt meter (DVM) to do any troubleshooting. Anyway.....your cart has TWO independent circuits. the Low amperage circuit and the High amperage. The fact that the solenoid CLICKS is a good thing, that means that the Low Amp circuit is good. Now to get to the HIGH Amp circuit. Obviously since you aren't getting power to the motor, there is something within the circuit amiss. here is the drawing. the RED and BLUE cables are hi-lighted. you need to trace them all out and double check every connection.
Series Cart Wiring Diagram.jpg |
05-10-2016, 09:11 AM | #3 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: ez go wont run
The NPX control is a little different than the OEM Curtis control. See below
|
05-10-2016, 09:59 AM | #4 |
Not Yet Wild
Join Date: Apr 2016
Posts: 37
|
Re: ez go wont run
iam going out to trace wiring now to see what i can find. thank you i will let you know
|
05-10-2016, 12:03 PM | #5 |
Not Yet Wild
Join Date: Apr 2016
Posts: 37
|
Re: ez go wont run
I checked all the connections and all are good.put the volt meter on pin 1 black wire showed .97 pushed on pedal and by the time got to floor read13.24 then done 2pin which is white wire start at .27 by the time got to the floor was11.00. by what iam reading the throttle signal should be 10v and then go down to 6v that is with the alltrax controller. am i seeing this wright
|
05-10-2016, 12:46 PM | #6 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: ez go wont run
Quote:
Measure the voltage between the two pins on the NPX controller with the black and white wires attached. Should be 10V with pedal up and 6V with pedal down. |
|
05-10-2016, 01:08 PM | #7 |
Not Yet Wild
Join Date: Apr 2016
Posts: 37
|
Re: ez go wont run
when i go to the 2 pins it shows .7 pedal down 2.5
|
05-10-2016, 01:40 PM | #8 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: ez go wont run
I screwed up. I should have said, with the pedal pushed just far enough for the solenoid to click, the voltage should be 10V and 6V with pedal pushed all the way down.
A series type controller isn't turned on until the solenoid clicks, which might explain the 0.7V reading, however, the pedal down voltage is way off. Could be water in the pedal box, a bad ITS sensor, or a partial short between the black and white wires someplace, or a bad controller. Pull the black and white wires off and measure the voltage between Pin 1 & 2. What is the voltage when the green LED on the controller is on? |
05-10-2016, 02:07 PM | #9 |
Not Yet Wild
Join Date: Apr 2016
Posts: 37
|
Re: ez go wont run
it is 1.1 pulling the white & black
|
05-10-2016, 02:15 PM | #10 |
Not Yet Wild
Join Date: Apr 2016
Posts: 37
|
Re: ez go wont run
sorry the green led is 38v
|
|
|
Similar Threads | ||||
Thread | Forum | |||
05 president wont roll in tow mode and wont run at wot | Electric Club Car | |||
Ezgo dcs solenoid clicks but wont disengage and wont move | Electric EZGO | |||
g-9 wont run | Gas Yamaha | |||
97 c c wont do anything | Electric Club Car | |||
Wont turn left and now wont turn right | Electric EZGO |