|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
12-28-2019, 01:02 PM | #1 |
Not Yet Wild
Join Date: Dec 2019
Posts: 33
|
48v precedent does nothing
Hoping for some advice here. Just signed up and have a 2011 club car precedent. Was driving last week and it just stopped. When I put it in reverse it buzzed for a sec and stopped. No reverse, no forward. I plugged it into the charger and does not click on. Checked voltage and it reads 50ish volts. Forward reverse switch has power at it in forward and in reverse. Any advice on where to go from here would be awesome!
Sent from my iPhone using Tapatalk |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-28-2019, 10:10 PM | #2 |
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: 48v precedent does nothing
(One wheel jacked up) Get your DVM and place the Black probe on the pack Neg and then with the key On, cart in Fwd, and Go Pedal depressed far enough to hear the microswitch click, take the Red probe and check to see if you have pack voltage in the following pins at the controller: Pin 5 - Lgt Blue (must be >30v), Pin 6 - Green, Pin 8 - Brown, Pin 9 - Grey, and Pin 10 - Tan.
|
12-28-2019, 10:11 PM | #3 |
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: 48v precedent does nothing
PS- Welcome!
|
12-28-2019, 11:49 PM | #4 |
Not Yet Wild
Join Date: Dec 2019
Posts: 33
|
Re: 48v precedent does nothing
Ok great...thank you! I will check first thing in the morn. To be sure you mean the harness at the pedal?
Sent from my iPhone using Tapatalk |
12-29-2019, 10:09 AM | #5 |
Not Yet Wild
Join Date: Dec 2019
Posts: 33
|
Re: 48v precedent does nothing
Good morning! So I am reading this again and I see you are saying harness at the controller. So that’s on the back of this board. There a truck to leaving this together and checking the pins? Seems like I can’t get to the harness at the controller without pulling that board out and going to the back of it that way.
Sent from my iPhone using Tapatalk |
12-29-2019, 01:49 PM | #6 |
Not Yet Wild
Join Date: Dec 2019
Posts: 33
|
Re: 48v precedent does nothing
So I found the access panel in the back to leave the board in place. Was checking the solenoid and the two main terminal and the two smaller have pack power all the time soon as key is on? Was trying to check the controller wires but having a hard time telling the different colors..
Sent from my iPhone using Tapatalk |
12-29-2019, 02:00 PM | #7 |
Not Yet Wild
Join Date: Dec 2019
Posts: 33
|
Re: 48v precedent does nothing
Nolefan4ever I should have added..I would count top left of plug to right and back probe these?
Sent from my iPhone using Tapatalk |
12-29-2019, 09:42 PM | #8 |
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: 48v precedent does nothing
Look at the White wire to identify Pin #1.
And yes, the access hatch is where you want to check. |
12-30-2019, 05:53 PM | #9 |
Not Yet Wild
Join Date: Dec 2019
Posts: 33
|
Re: 48v precedent does nothing
Nolefan4ever. I checked all the pins. 5 has 0 voltage 6 has 50v as well as 8,9,and 10. Pin 6 gets voltage when pedal is depressed and 8,9,10 have it all the time. Hope this tells a story of absolute problem identification! Lol
Sent from my iPhone using Tapatalk |
12-30-2019, 07:22 PM | #10 |
Not Yet Wild
Join Date: Dec 2019
Posts: 33
|
Re: 48v precedent does nothing
I should also add that my light on the dash does not come on.
Sent from my iPhone using Tapatalk |
|
|
Similar Threads | ||||
Thread | Forum | |||
Rxv doesn’t run, controller? | Electric EZGO | |||
Ds solenoid doesn’t always go | Electric Club Car | |||
RXV doesn’t go | Electric EZGO | |||
Engine doesn’t want to cut off | Gas Club Car | |||
Sputters, Stalls & Sometimes Doesn’t Want to Move - 2010 Precedent | Electric Club Car |