|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
02-25-2017, 03:55 PM
|
#11 |
|
Getting Wild
Join Date: Feb 2017
Location: Texarkana, Tx
Posts: 87
|
Re: Wiring reducer setup
One quick other question before I start the wiring this evening. On the first picture u made do I have to wire a switch in or can I just run it straight to battery positive and rely on the key action for turning reducer on and off since I'm going to splice into hot key switch wire?
Sent from my iPhone using Tapatalk |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
02-25-2017, 04:15 PM
|
#12 |
|
Guest
Posts: n/a
|
Re: Wiring reducer setup
you just need to tie in the #9 pin wire
the on off switch is for shutting it down without the key switch so you dont need it or to wire it to batteries here is how i would wire it  |
|
|
|
02-25-2017, 04:49 PM
|
#13 |
|
Getting Wild
Join Date: Feb 2017
Location: Texarkana, Tx
Posts: 87
|
Re: Wiring reducer setup
Sweet man. Couldn't have done it without you!
Sent from my iPhone using Tapatalk |
|
|
|
|
02-25-2017, 04:51 PM
|
#14 |
|
Guest
Posts: n/a
|
Re: Wiring reducer setup
 |
|
|
|
02-25-2017, 06:14 PM
|
#15 |
|
Getting Wild
Join Date: Feb 2017
Location: Texarkana, Tx
Posts: 87
|
Re: Wiring reducer setup
CTD does this look right? When I hooked everything up and turned key on my battery meter was out of control flashing red and my lights would not work.
First pic is reducer and fuse block installed and wired Second pic is where I spliced the neg fromreducer in with neg coming back for battery meter 3rd is where I spliced I hope the 9th pin like in the pic. |
|
|
|
|
02-25-2017, 06:43 PM
|
#16 | |
|
Gone Insane
 Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
|
Re: Wiring reducer setup
Quote:
|
|
|
|
|
|
02-25-2017, 06:52 PM
|
#17 |
|
Getting Wild
Join Date: Feb 2017
Location: Texarkana, Tx
Posts: 87
|
Re: Wiring reducer setup
What would u suggest to join or jump wires? Do all my hook ups look ok?
Sent from my iPhone using Tapatalk |
|
|
|
|
02-25-2017, 07:52 PM
|
#18 |
|
Guest
Posts: n/a
|
Re: Wiring reducer setup
to me you are spliced in to #2 on j1 which should give you power all the time... i guess its upside down from diagram ...the dark green is #10
1 make sure you are in run 2 make sure fuse is good 3 test reducer ... take off your tap and run it to the main pack positive ... test output make sure charger is not plugged in |
|
|
|
02-25-2017, 09:22 PM
|
#19 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Wiring reducer setup
Also, this wiring method (and this type dc/DC convertor without a enable/trigger wire) is drawing all the current through the reed switch & key switch, 2 common failure points on a Txt.
|
|
|
|
|
02-25-2017, 10:25 PM
|
#20 |
|
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,214
|
Re: Wiring reducer setup
Sorry, I came in late on this and don't mean to butt in but would like to add something that may help. These reducers may take a few seconds to energize before they work.
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Voltage reducer, lights, stereo setup.... | Electric Club Car | |||
| Reducer wiring help | Electric EZGO | |||
| Wiring schematic for 5 solenoid setup | Electric EZGO | |||
| Club car clone wiring setup | Clone Engine Swaps | |||
| wiring an 77 engine to 87 setup | Gas EZGO | |||
Linear Mode
