|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
03-19-2022, 09:44 AM | #1 |
Not Yet Wild
Join Date: May 2016
Posts: 31
|
Alltrax Controller Programming
Can someone point me in the right direction on programming the Alltrax Controllers. I have a SR48500 running my 36v cart. I'm upgrading to 48v Lithium and would like to know if I need to change anything and or adjust the controller for this.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-19-2022, 11:00 AM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Alltrax Controller Programming
Contact your battery supplier or research your battery specifications. Find the max draw and set the max limit in the controller to match. Check to see the max voltage setting on the controller is set to max to accept the higher voltage battery
|
03-19-2022, 03:48 PM | #3 |
Not Yet Wild
Join Date: May 2016
Posts: 31
|
Re: Alltrax Controller Programming
sounds good! Do I need any special program download or cable to access the controller? When I bought it from you, you sent it for me.
|
03-19-2022, 04:08 PM | #4 |
Gone Wild
Join Date: May 2012
Location: Rio Verde, Az
Posts: 7,187
|
Re: Alltrax Controller Programming
You get the program from Alltrax web site. You use a USB cable to connect to it.
|
03-19-2022, 05:53 PM | #5 |
Not Yet Wild
Join Date: May 2016
Posts: 31
|
Re: Alltrax Controller Programming
Thanks for the help everyone!
|
04-21-2022, 03:45 PM | #6 |
Not Yet Wild
Join Date: May 2016
Posts: 31
|
Re: Alltrax Controller Programming
I finally got everything wired in yesterday and just adjusted the controller. I have a problem, the cart wants to move, but only jitters a few inches and stops. When I adjusted the voltage settings, dose the throttle setting change when you do this? I did not change or look at any of those setting on the Throttle curve page. Was planning to take this to camp tomorrow, so any help would be greatly appreciated!!!
|
04-21-2022, 05:02 PM | #7 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Alltrax Controller Programming
The setting you should have changed was the maximum battery amperage draw. This does not change the throttle type or curve.
Check you actual battery pack voltage when you try to go and the cart just jitters. |
04-28-2022, 11:32 AM | #8 |
Gone Wild
Join Date: Jan 2013
Location: Saint Petersburg, FL
Posts: 2,089
|
Re: Alltrax Controller Programming
Make sure your max V in the Alltrax is high enough for the battery V. I adjusted mine all the way up because the lithium has a much higher max V than the lead acid did.
I also adjusted the low V cutoff to act as a safety for my lithium in case the BMS fails. I also found out that with 350 fewer pounds in the cart and the V higher that I ended up needing to mellow out my throttle mapping because starting from a dead stop was too aggressive... But that's after you get the cart moving normally. |
|
|
Similar Threads | ||||
Thread | Forum | |||
Alltrax Controller Programming | Gas EZGO | |||
Programming new alltrax controller... | Electric Club Car | |||
Bad OBC after programming Alltrax controller? possible? | Electric Club Car | |||
Programming alltrax controller | Electric EZGO | |||
what is the best programming for an alltrax controller | Electric EZGO |