|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
04-04-2014, 03:07 PM | #11 |
Getting Wild
Join Date: Jul 2010
Posts: 119
|
Re: G16 dying out after warm up
Anyone know who sells TCI's? I check a lot of the sponsor sites and most don't carry them and I didn't see any that carry Yamaha brand / OEM
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-04-2014, 06:13 PM | #12 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: G16 dying out after warm up
If you can't find a site sponsor that sells the OEM, do a web search for part# JN-85640-01-00 or call the nearest Yamaha golf car dealer. I highly recommend NOT useing an aftermarket TCI.
|
04-04-2014, 06:49 PM | #13 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G16 dying out after warm up
Jn6-85640-01-00
|
04-04-2014, 06:56 PM | #14 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: G16 dying out after warm up
Me bad...thanks for fixing it cgtech.
|
04-12-2014, 07:31 PM | #15 |
Getting Wild
Join Date: Jul 2010
Posts: 119
|
Re: G16 dying out after warm up
I bought the new YAMAHA OEM TCI. I was going to put it in today then I smell fuel. I check my oil and its got gas in it again. (I had another thread about this) Installed a new carb and new fuel pump and still have gas. I'm going to get the new TCI in tomorrow. Any tips on the install or gas in the oil?
fuel lines are run the same as stock. |
04-13-2014, 03:05 AM | #16 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G16 dying out after warm up
do you drive all short trips? If the engine never gets hot, unburned fuel will get past rings into oil. I believe some longer trips "burns" the fuel out of the oil. I am assuming you have already looked at the spark plug.
|
04-13-2014, 11:01 AM | #17 |
Getting Wild
Join Date: Jul 2010
Posts: 119
|
Re: G16 dying out after warm up
Dumb question. how do you get the bolt out on the bottom of the plastic motor shoud to get to the TCI? I can't get a wrench on it. the skidplate is riveted to the frame
|
04-13-2014, 11:44 AM | #18 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G16 dying out after warm up
1/4 rachet, extension, u-joint (wobbly), short 10mm socket , dexterious fingers.
|
04-13-2014, 11:49 AM | #19 |
Getting Wild
Join Date: Jul 2010
Posts: 119
|
Re: G16 dying out after warm up
phew.... cut a custom 10mm wrench.. PITA.
Now how do you set the TCI? paper between the tci and flywheel? I'll tell you what. I don't know what I'd do without the internet. I appreciate your help tremendously. |
04-13-2014, 12:27 PM | #20 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G16 dying out after warm up
I use the old "points trick", matchbook cover. Or something similar.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
battery dying | Gas Yamaha | |||
My cart is dying! | Gas Club Car | |||
Battery keeps dying | Gas EZGO | |||
Dying Trojans | Electric Club Car | |||
battery keeps dying-why? | Gas Yamaha |