|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
10-24-2020, 07:18 PM | #1 |
Not Yet Wild
Join Date: Aug 2016
Posts: 38
|
Programming cable connector / adaptor
Does anyone know the type of connector used on the Curtis 1206AC controller? It appears to be a small round male 4-pin connector. I would like to adapt this in to anything else (wires) to connect to the PC.
Any information you could provide would be helpful. For example, the type of connector used or a part # i could purchase to connect to it. Thanks -e |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-24-2020, 07:50 PM | #2 |
Gone Wild
Join Date: Mar 2014
Location: NE Indiana & SW Florida
Posts: 3,235
|
Re: Programming cable connector / adaptor
The Tyco plug is TE Connectivity part # 1445390-1, the 4 female socket pins are part # 770986-1, and a cable strain relief is part # 1445730-1.
The Mini-Fit Jr end is a Molex socket, part # 39-01-3043, and 4 male pins, part # 39-00-0049. |
10-25-2020, 02:37 AM | #3 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Programming cable connector / adaptor
Dang, this guy is good. Almost like he done this before....
|
10-25-2020, 10:31 AM | #4 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,146
|
Re: Programming cable connector / adaptor
Or if you are a visual person. Also if you want to save a little time you can buy an ATX power supply extension and cut the one end off.
|
12-23-2020, 11:33 AM | #5 |
Not Yet Wild
Join Date: Aug 2016
Posts: 38
|
Re: Programming cable connector / adaptor
What are the requirements for the serial cable? Is it RS232, inverted RS232, TTL, Inverted TTL? What are the voltage levels of the bus? I am trying to get it to work with an inverted TTL connection but its not working yet. Perhaps i missed something. Thanks.
|
12-23-2020, 12:14 PM | #6 | |
Gone Wild
Join Date: May 2016
Location: Central Alabama
Posts: 1,048
|
Re: Programming cable connector / adaptor
Quote:
https://www.buggiesgonewild.com/show...ght=programmer |
|
12-26-2020, 01:00 PM | #7 |
Not Yet Wild
Join Date: Aug 2016
Posts: 38
|
Re: Programming cable connector / adaptor
Have plenty of those laying around :)
|
12-26-2020, 01:01 PM | #8 |
Not Yet Wild
Join Date: Aug 2016
Posts: 38
|
Re: Programming cable connector / adaptor
Superp. Thank you. Do you recommend converting to the square connector or staying with the round one? I would like to attach my laptop. I am having trouble making it work so far. I have been slipping pins over the pins, but still havent been successful. Is it RS232 or TTL? I have tried both; with inversion on the TTL as well. The controller is a 1206AC-5201 and im using the 1314 PC software. USB to RS232 adapter or USB to TTL adapters are verified working.
|
12-27-2020, 11:47 AM | #9 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,146
|
Re: Programming cable connector / adaptor
You need the 3 volt TTL cable. Go read this thread for some help. https://www.buggiesgonewild.com/show...=15316&page=99
|
01-08-2022, 07:04 PM | #10 |
Not Yet Wild
Join Date: Aug 2016
Posts: 38
|
Re: Programming cable connector / adaptor
You dont happen to know the bus bit rate and rx/tx line polarity do you? thanks. -e
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Battery Connector cable with attached blue cable | Electric Club Car | |||
Battery cable connector sizes | Electric Club Car | |||
Battery cable and connector extreme hot and melt | Electric EZGO | |||
Negative Battery Cable Connector Broke | Gas EZGO |