|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
10-01-2018, 12:06 PM | #1 |
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Removing Axle
Guy brought me an electric cart to fix noise in left hub. I removed wheel and hub had been welded to axle. Seems threads were bad and now he wants all that fixed. I had to grind off the end of the axle to get down to the hub so it would come off. Now I have to get the axle out. Anybody got any ideas. I have tried vice grips locked on the spline but they wont stay. Is there any drill bits that will drill the end of the axle? Then I will have to thread the hole to get a slide hammer on it. Any ideas will be greatly appreciated.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-01-2018, 12:26 PM | #2 | |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Removing Axle
Quote:
|
|
10-01-2018, 05:30 PM | #3 |
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Removing Axle
Yes I removed the clip. I will get a pic.
|
10-01-2018, 06:08 PM | #4 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Removing Axle
Do you have a welder?
Are any threads left on the axle? |
10-01-2018, 06:09 PM | #5 |
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Removing Axle
Sorry I had to send pic by email at scottyb@cartsunlimited.net
|
10-01-2018, 06:11 PM | #6 |
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Removing Axle
No welder but I have been looking. No threads left. About an inch and a half of spline sticking out.
|
10-01-2018, 06:15 PM | #7 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Removing Axle
Ouch - Maybe you can drop the pan and drive or pry the axle out from the middle?
|
10-01-2018, 06:18 PM | #8 |
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Removing Axle
I did drop the pan and no way to get to it. I think I will get me a welder and go that route. Thanks for the help.
|
10-01-2018, 06:28 PM | #9 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Removing Axle
sounds like a good excuse to get you a welder
Tack a slide hammer affair on there. Don't have to be fancy. Even a small length rod with a stop welded on and using the old drum as a slide hammer will do. You will need new seals and bearings, along with the axles and drums |
10-01-2018, 06:29 PM | #10 |
Gone Wild
Join Date: Sep 2016
Location: Ludington Michigan
Posts: 168
|
Re: Removing Axle
Drill and tap the end of the axle for a slide hammer? Not sure how hard axles are.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Removing CC DS Axle Shafts? | Electric Club Car | |||
2012 precedent- how to remove rear axle shaft/replace axle seal? | Electric Club Car | |||
Removing the rear axle snap ring? | Gas Club Car | |||
Removing axle shaft | Electric Club Car | |||
Removing Precedent Axle | Electric Club Car |