lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Yamaha
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles



Post New Thread  Reply
 
Thread Tools Display Modes
Old 08-29-2007, 02:21 PM   #1
jwblocal701
Not Yet Wild
 
Join Date: Aug 2007
Posts: 44
Default carb jetting

OK i seen alot of talk about jetting the carb but no discussion on where to et the jet? do i need a new gasket set? drill bit size?
and i know i can then get a k&n air filter and if in not mistaken i take the hose from the original airbox and just lay it aside??
If i jet the carb do i need to readjust the setting on it or is factory setting good

I know alot of questions but i wanna get a little more pep in my step and im sure that will help especially since i just lifted it and put bigger tires on it
jwblocal701 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 08-29-2007, 02:50 PM   #2
TheNewGuy
Admin/Moderator
 
TheNewGuy's Avatar
Yamaha
 
Join Date: Dec 2006
Location: Ohio
Posts: 16,857
Default Re: carb jetting

You will only need to change 1 jet. Remove the bowl from the carb and the
main jet is the one facing forward (number 17 on diagram). You can open the
jet diameter or purchase a new jet. When I did this I bought a couple new
ones and tried different sizes. .048 - .052 inside diameter is the range that
should work the best. OR, buy one ready to go...Check the jet link.

The hose coming from the valve cover is a vent, you can run it down and
point it at the ground using a zip tie to hold it. You may have a drip of oil
coming out of it from time to time.

Diagram, http://www.tntgolfcar.com/yamparts.php?diagramid=251

Jet link, http://cartpartsplus.com/product_inf...ca65eedfbc2828

TheNewGuy is offline   Reply With Quote
Old 08-29-2007, 02:53 PM   #3
jwblocal701
Not Yet Wild
 
Join Date: Aug 2007
Posts: 44
Default Re: carb jetting

so the jet from CCP is ready to go just take my old out and install the new one?
do i need to drill it bigger the hole it goes into
jwblocal701 is offline   Reply With Quote
Old 08-29-2007, 03:08 PM   #4
TheNewGuy
Admin/Moderator
 
TheNewGuy's Avatar
Yamaha
 
Join Date: Dec 2006
Location: Ohio
Posts: 16,857
Default Re: carb jetting

If you buy the one from CPP, it is ready to go!!!! Just screw it in.

TheNewGuy is offline   Reply With Quote
Old 08-29-2007, 03:14 PM   #5
jwblocal701
Not Yet Wild
 
Join Date: Aug 2007
Posts: 44
Default Re: carb jetting

and you get alot more power huh is it noticable im gonna order one
jwblocal701 is offline   Reply With Quote
Old 08-29-2007, 03:16 PM   #6
TheNewGuy
Admin/Moderator
 
TheNewGuy's Avatar
Yamaha
 
Join Date: Dec 2006
Location: Ohio
Posts: 16,857
Default Re: carb jetting

You will notice a difference. Talk to Tom at CPP, he can fill you in.

TheNewGuy is offline   Reply With Quote
Old 08-31-2007, 12:06 PM   #7
jwblocal701
Not Yet Wild
 
Join Date: Aug 2007
Posts: 44
Default Re: carb jetting

if i wanted to drill my carb which is the best size bit then?
jwblocal701 is offline   Reply With Quote
Old 08-31-2007, 02:13 PM   #8
shawn.m
Gone Wild
 
shawn.m's Avatar
 
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,882
Default Re: carb jetting

just buy mikuni carb jets from your local motorcycle shop. only $2 each. I run a 132 when I have the stock muffler on my cart, 152 when i have the dirt bike exhaust
shawn.m is offline   Reply With Quote
Old 08-31-2007, 06:14 PM   #9
Punisher
Not Yet Wild
 
Join Date: Aug 2007
Location: Central Point, Oregon
Posts: 20
Default Re: carb jetting

Shawn is your motor stock with exception of the air cleaner, and what dirt bike exhaust do you run?
Punisher is offline   Reply With Quote
Old 08-31-2007, 07:23 PM   #10
shawn.m
Gone Wild
 
shawn.m's Avatar
 
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,882
Default Re: carb jetting

modifed air filter box, welded on a kx250 2 stroke muffler on it. i have a extra head that I ported that I am going to try out eventually, really need to get the head cut before I put it on. I did but a timing advance key but misplaced it.

shawn.m is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Yamaha


Thread Tools
Display Modes



All times are GMT -5. The time now is 09:12 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.