Danaher hand held

Titansnbucs · 03-31-2020, 08:39 PM

Anyone near winter Haven Fl have a hand held in need of help thanks in advance
Pm me

usgicollector · 04-01-2020, 12:24 AM

You need three posts before you can send or receive a pm.

Go ahead and tell us what is wrong.

Titansnbucs · 04-01-2020, 08:34 AM

I’ve been going through tests in trouble shooting guide the brake gets voltage on intermittent basis when it’s there motor rotates other wise no go I’m lost

usgicollector · 04-01-2020, 10:45 AM

It sounds like your not passing the start-up test.

I left Florida a week ago or I could have helped. I would start by looking at the wires inside the wire harness.

Maybe a member with a Danaher handheld close to you will help out.

Titansnbucs · 04-02-2020, 07:20 AM

Still needing danaher handheld

Titansnbucs · 04-04-2020, 03:39 PM

Replaced encoder bearing all’s fine no it can go bye bye

hammrhed71 · 04-08-2020, 06:09 PM

How'd you figure that out? lol Handheld?

madreg98 · 06-30-2020, 04:02 PM

I inherited a 2011, 2012 or 2013 rxv 48v (Model information sticker is missing) from my son. He said he was operating and the cart died. Symptoms: Initially does not perform start-up but solenoid clicks and then clicks again. Solenoid checked good but replaced with new anyhow. No change. Had Controller (Danaher ACD4805) rebuilt. Reinstalled and tried again with some undefinable electrical sounds and now no start-up, no solenoid activation and run/tow does not work. Totally dead. Checked fuses, charging port, start switch, run/tow switch. do not have a diagnostic tool, just volt meter. Going to check brake and throttle. Does this sound like a wacked controller? Would hate to buy another to find out it's still good or burn out another. Any help would be greatly appreciated.

usgicollector · 06-30-2020, 04:15 PM

Quote:

Originally Posted by madreg98

I inherited a 2011, 2012 or 2013 rxv 48v (Model information sticker is missing) from my son. He said he was operating and the cart died. Symptoms: Initially does not perform start-up but solenoid clicks and then clicks again. Solenoid checked good but replaced with new anyhow. No change. Had Controller (Danaher ACD4805) rebuilt. Reinstalled and tried again with some undefinable electrical sounds and now no start-up, no solenoid activation and run/tow does not work. Totally dead. Checked fuses, charging port, start switch, run/tow switch. do not have a diagnostic tool, just volt meter. Going to check brake and throttle. Does this sound like a wacked controller? Would hate to buy another to find out it's still good or burn out another. Any help would be greatly appreciated.

What state do you live in?

madreg98 · 06-30-2020, 04:16 PM

I'm in St Augustine, FL

03-31-2020, 08:39 PM	#1
Titansnbucs Not Yet Wild Join Date: Mar 2020 Posts: 4	Danaher hand held Anyone near winter Haven Fl have a hand held in need of help thanks in advance Pm me
Titansnbucs Not Yet Wild Join Date: Mar 2020 Posts: 4

04-01-2020, 12:24 AM	#2
usgicollector Gone Wild Join Date: Mar 2014 Location: NE Indiana & SW Florida Posts: 3,238	Re: Danaher hand held You need three posts before you can send or receive a pm. Go ahead and tell us what is wrong.

04-01-2020, 08:34 AM	#3
Titansnbucs Not Yet Wild Join Date: Mar 2020 Posts: 4	Re: Danaher hand held I’ve been going through tests in trouble shooting guide the brake gets voltage on intermittent basis when it’s there motor rotates other wise no go I’m lost
Titansnbucs Not Yet Wild Join Date: Mar 2020 Posts: 4

04-01-2020, 10:45 AM	#4
usgicollector Gone Wild Join Date: Mar 2014 Location: NE Indiana & SW Florida Posts: 3,238	Re: Danaher hand held It sounds like your not passing the start-up test. I left Florida a week ago or I could have helped. I would start by looking at the wires inside the wire harness. Maybe a member with a Danaher handheld close to you will help out.

04-02-2020, 07:20 AM	#5
Titansnbucs Not Yet Wild Join Date: Mar 2020 Posts: 4	Re: Danaher hand held Still needing danaher handheld
Titansnbucs Not Yet Wild Join Date: Mar 2020 Posts: 4

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

04-04-2020, 03:39 PM	#6
Titansnbucs Not Yet Wild Join Date: Mar 2020 Posts: 4	Re: Danaher hand held Replaced encoder bearing all’s fine no it can go bye bye
Titansnbucs Not Yet Wild Join Date: Mar 2020 Posts: 4

04-08-2020, 06:09 PM	#7
hammrhed71 Not Yet Wild Join Date: Sep 2018 Posts: 43	Re: Danaher hand held How'd you figure that out? lol Handheld?
hammrhed71 Not Yet Wild Join Date: Sep 2018 Posts: 43

06-30-2020, 04:02 PM	#8
madreg98 Not Yet Wild Join Date: Feb 2012 Posts: 8	Re: Danaher hand held I inherited a 2011, 2012 or 2013 rxv 48v (Model information sticker is missing) from my son. He said he was operating and the cart died. Symptoms: Initially does not perform start-up but solenoid clicks and then clicks again. Solenoid checked good but replaced with new anyhow. No change. Had Controller (Danaher ACD4805) rebuilt. Reinstalled and tried again with some undefinable electrical sounds and now no start-up, no solenoid activation and run/tow does not work. Totally dead. Checked fuses, charging port, start switch, run/tow switch. do not have a diagnostic tool, just volt meter. Going to check brake and throttle. Does this sound like a wacked controller? Would hate to buy another to find out it's still good or burn out another. Any help would be greatly appreciated.
madreg98 Not Yet Wild Join Date: Feb 2012 Posts: 8

06-30-2020, 04:16 PM	#10
madreg98 Not Yet Wild Join Date: Feb 2012 Posts: 8	Re: Danaher hand held I'm in St Augustine, FL
madreg98 Not Yet Wild Join Date: Feb 2012 Posts: 8

Similar Threads
Thread	Forum
Using curtis hand held with 07 precedent	Electric Club Car
hand held porgrammer	Electric Club Car
looking for a 48v hand held code reader	Electric Club Car
Curtis hand held programmer	Electric Club Car
Curtis hand held programmer	Electric Club Car