|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
12-09-2012, 11:01 AM
|
#1 |
|
Not Yet Wild
Join Date: Nov 2012
Posts: 5
|
2001ezgo series cart
Gentleman, i have replaced the f & R switch on my cart, put new 4g wires on, now the cart will not do anything. I have lights, switches click, i have ohm all wires. When you turn the key battery guage wont come on. i need some help , everything i have looked at on here it seems i have correct.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
12-09-2012, 12:49 PM
|
#2 |
|
Techno-Nerd
 Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 2001ezgo series cart
Are the new cables connected as shown?
What is the battery pack voltage? Does solenoid click when you push pedal? |
|
|
|
|
12-09-2012, 03:26 PM
|
#3 |
|
Not Yet Wild
Join Date: Nov 2012
Posts: 5
|
Re: 2001ezgo series cart
Yes 36 volts batteries are hooked in that order solenoid does not click thinking now it may be bad ignition switch,
|
|
|
|
|
12-09-2012, 06:04 PM
|
#4 |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 2001ezgo series cart
Could be, but the F/R microswitch (MS-2), the pedal microswitch (MS-3) and the reed switch (Labeled Ignition Interlock on schematic) are more common failures.
Here is a schematic of a series cart with the solenoid activation circuit highlighted. |
|
|
|
|
12-10-2012, 10:25 AM
|
#5 |
|
Not Yet Wild
Join Date: Nov 2012
Posts: 5
|
Re: 2001ezgo series cart
well sir i have checked the reed switch, ms-2 and ms-3, key is good. did solenoid check with what i found on the forum, and still no go.
|
|
|
|
|
12-10-2012, 10:49 AM
|
#6 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: 2001ezgo series cart
Does the solenoid engage when you try to go?
|
|
|
|
|
12-10-2012, 10:51 AM
|
#7 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: 2001ezgo series cart
Can you remove the shift linkage and manually shift the F&R with a 9/16 wrench to insure it is going ALL THE WAY into gear?
The rotary cam must go hit the stop to make the contacts. |
|
|
|
|
12-10-2012, 11:17 AM
|
#8 |
|
Not Yet Wild
Join Date: Nov 2012
Posts: 5
|
Re: 2001ezgo series cart
to the forum thanks, it was the reed switch bypassed that, now forward is reverse and vice-versa. again thanks for the help.
|
|
|
|
|
12-10-2012, 11:20 AM
|
#9 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: 2001ezgo series cart
Swap S1 and S2 at the motor or the 9 and 3 o'clock connections on the F&R
 |
|
|
|
|
12-10-2012, 12:12 PM
|
#10 |
|
Not Yet Wild
Join Date: Nov 2012
Posts: 5
|
Re: 2001ezgo series cart
it runs like a champ now fellas, thanks again for the help. Merry Christmas.
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| How compatible would a DCS cart be with a newer Series cart? | Electric EZGO | |||
| Pot from DCS in a Series cart | Electric EZGO | |||
| How to DIY Series Cart | Electric EZGO | |||
| Upgrading cart from EZGO Series cart | Electric EZGO | |||
| 04 series cart | Electric EZGO | |||
Linear Mode
