Personality switch for Alltrax

scmoose · 07-09-2019, 04:46 PM

Switch

Sent from my SM-G950U using Tapatalk

NoleFan4Ever · 07-09-2019, 05:10 PM

That's the one I use. It's hidden up in the battery compartment above the eyeline.

Sergio · 07-09-2019, 05:12 PM

If you connect two wires without using the switch and User1 and User2 become active, then you likely have a wiring problem.

Do a continuity test on the cable to make sure is not pinched somewhere and causing a short.

scmoose · 07-09-2019, 08:35 PM

Im not sure why both user buttons light up in the monitor tab of the toolkit program when my switch is position 1 or 2, but it seems to be responding to the parameters I have set in the tool kit. Position 0 on my switch it hauls but, position 1 or 2 is more like a normal cart, which is how I have the program set.

scmoose · 07-09-2019, 08:35 PM

I think one of my terminals in the plug I made up may not have been pushed in far enough into the connector.

Sergio · 07-10-2019, 06:36 AM

Quote:

Originally Posted by scmoose

I think one of my terminals in the plug I made up may not have been pushed in far enough into the connector.

If it was shorting against the pin next to it, that would explain why both User1 and User2 were always powered together.

scmoose · 07-10-2019, 07:51 AM

No i don't think it was. As it sits, both user 1 and 2 show on at the same time in the monitor folder of the toolkit when my switch is in position 1 or 2. Hell if I know what is going on.

Sent from my SM-G950U using Tapatalk

Sergio · 07-10-2019, 08:12 AM

Quote:

Originally Posted by scmoose

No i don't think it was. As it sits, both user 1 and 2 show on at the same time in the monitor folder of the toolkit when my switch is in position 1 or 2. Hell if I know what is going on.

Sent from my SM-G950U using Tapatalk

It has to be the cable, connector or the switch, since only one of the two pins has power at the time, they cannot both show ON in the monitor.

scmoose · 07-10-2019, 08:18 AM

I will check the switch with a meter tonight. So If I understand correct, when my switch is in the 1 position, I should show voltage there, but zero volts on the 2nd position pin correct? Nolefan4ever how do you have your switch wired up? Do you have power going to the center pin?

Sergio · 07-10-2019, 08:23 AM

Quote:

Originally Posted by scmoose

I will check the switch with a meter tonight. So If I understand correct, when my switch is in the 1 position, I should show voltage there, but zero volts on the 2nd position pin correct? Nolefan4ever how do you have your switch wired up? Do you have power going to the center pin?

Correct, power goes to the center pin.

In the center position there should be no power to either side.

When you place the switch in one of the other two positions, only the pin on the opposite side that is depressed should have power.

07-09-2019, 04:46 PM	#11
scmoose Gone Wild Join Date: May 2018 Location: Fuquay NC Posts: 181	Re: Personality switch for Alltrax Switch Sent from my SM-G950U using Tapatalk

07-09-2019, 05:10 PM	#12
NoleFan4Ever MOD of all BS! Join Date: Sep 2011 Location: Florida Posts: 17,477	Re: Personality switch for Alltrax That's the one I use. It's hidden up in the battery compartment above the eyeline.

07-09-2019, 05:12 PM	#13
Sergio Gone Wild Join Date: Sep 2012 Location: Charlotte, NC Posts: 9,329	Re: Personality switch for Alltrax If you connect two wires without using the switch and User1 and User2 become active, then you likely have a wiring problem. Do a continuity test on the cable to make sure is not pinched somewhere and causing a short.

07-09-2019, 08:35 PM	#14
scmoose Gone Wild Join Date: May 2018 Location: Fuquay NC Posts: 181	Re: Personality switch for Alltrax Im not sure why both user buttons light up in the monitor tab of the toolkit program when my switch is position 1 or 2, but it seems to be responding to the parameters I have set in the tool kit. Position 0 on my switch it hauls but, position 1 or 2 is more like a normal cart, which is how I have the program set.

07-09-2019, 08:35 PM	#15
scmoose Gone Wild Join Date: May 2018 Location: Fuquay NC Posts: 181	Re: Personality switch for Alltrax I think one of my terminals in the plug I made up may not have been pushed in far enough into the connector.

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

07-10-2019, 07:51 AM	#17
scmoose Gone Wild Join Date: May 2018 Location: Fuquay NC Posts: 181	Re: Personality switch for Alltrax No i don't think it was. As it sits, both user 1 and 2 show on at the same time in the monitor folder of the toolkit when my switch is in position 1 or 2. Hell if I know what is going on. Sent from my SM-G950U using Tapatalk

07-10-2019, 08:18 AM	#19
scmoose Gone Wild Join Date: May 2018 Location: Fuquay NC Posts: 181	Re: Personality switch for Alltrax I will check the switch with a meter tonight. So If I understand correct, when my switch is in the 1 position, I should show voltage there, but zero volts on the 2nd position pin correct? Nolefan4ever how do you have your switch wired up? Do you have power going to the center pin?

Similar Threads
Thread	Forum
Personality Plugs	Electric EZGO
Alltrax Personality Switch - Use and Profile Suggestions	Electric EZGO
Personality plug?	Electric EZGO
A couple of switch questions - Run/Tow and Alltrax "Personality"	Electric EZGO
Will the red ezgo personality plug help?	Electric EZGO