|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
07-10-2019, 09:20 AM | #21 |
Gone Wild
Join Date: Sep 2014
Location: Orlando, FL
Posts: 1,308
|
Re: Personality switch for Alltrax
I have used the same switch on several carts for the same function. Since they are cheap Chinese, I was not surprised when a new one failed /did not work right from the beginning. Check switch as Sergio says.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-10-2019, 04:09 PM | #22 |
Gone Wild
Join Date: May 2018
Location: Fuquay NC
Posts: 181
|
Re: Personality switch for Alltrax
Switch must be bad. I get 50 volts on middle terminal and 0 on the two outside terminals when switch is in the middle position. Move it to position 1, and I get 50V on position 2 but stray voltage on position 1, then vise versa when I move the switch to the 2nd position.
|
07-12-2019, 08:55 AM | #23 | |
Gone Wild
Join Date: Jan 2017
Location: Queensland Australia
Posts: 1,332
|
Re: Personality switch for Alltrax
Quote:
|
|
07-12-2019, 09:01 AM | #24 | |
Bonafide Nincompoop
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 8,987
|
Re: Personality switch for Alltrax
Quote:
|
|
06-10-2020, 04:27 PM | #25 |
Getting Wild
Join Date: Apr 2010
Posts: 81
|
Re: Personality switch for Alltrax
I am looking to build one of these on an XCT400 AMP (Yamaha G22).
The switches on the dash are illuminated and powered off a 48V to 12V reducer. Could I use a 12V relay to trigger the connection of the 48V KSI back into the correct molex pin, or would that be too many volts for the relay? Relay Diagram.jpg |
06-16-2020, 01:09 PM | #26 |
Not Yet Wild
Join Date: Mar 2020
Location: South Carolina
Posts: 45
|
Re: Personality switch for Alltrax
I'm looking to create one of these cables for my new Alltrax install. Where would be the best place to source all the parts?
Thanks for your help! |
06-23-2020, 08:04 PM | #27 |
Not Yet Wild
Join Date: Mar 2020
Location: South Carolina
Posts: 45
|
Re: Personality switch for Alltrax
...and to answer my own question - since I installed a new Alltrax controller I repurposed the Curtis programming cable and removed the pins from that molex connector (OMG! - what a pain to do from under the cart! ) and put it in a new molex connector that I got from Digi-Key. On the other end I used the three position switch that @Sergio used and so far so good. Very cool way to secure the cart and be able to switch to a toned down profile!
|
06-23-2020, 11:18 PM | #28 | |
Gone Wild
Join Date: Apr 2020
Location: 1000 Oaks, SOCAL
Posts: 424
|
Re: Personality switch for Alltrax
Quote:
I've been searching for awhile and can't seem to find a plug that looks the right shape to fit in the J4-5-6 socket. |
|
06-24-2020, 05:01 AM | #29 | |
Guest
Posts: n/a
|
Re: Personality switch for Alltrax
Quote:
Here you go. |
|
06-24-2020, 05:42 AM | #30 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: Personality switch for Alltrax
More parts and wiring info:
https://www.buggiesgonewild.com/show...03&page=24#240 |
|
|
Similar Threads | ||||
Thread | Forum | |||
Personality Plugs | Electric EZGO | |||
Alltrax Personality Switch - Use and Profile Suggestions | Electric EZGO | |||
Personality plug? | Electric EZGO | |||
A couple of switch questions - Run/Tow and Alltrax "Personality" | Electric EZGO | |||
Will the red ezgo personality plug help? | Electric EZGO |