08-28-2012, 08:18 AM | #1 |
Not Yet Wild
Join Date: Aug 2012
Posts: 57
|
Clutch work?
Is it worth pulling the spider when I have the clutch off to close up the belt to sheave in the primary clutch on the carts?
With a sled we try our best to get .020 belt to sheave with a new belt for a nice smooth take off. Is the extra space needed for offset in these carts. It seems there is no adjustment for offset. Cheers Don. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-30-2012, 02:33 PM | #2 |
Not Yet Wild
Join Date: Aug 2012
Posts: 57
|
Re: Clutch work?
No big clutch guys on here?
I find with sleds that when you close up the space at rest between the clutch movable sheave and the belt at rest you start to grab the belt sooner in the fly of the weights. This will give you more up shift because your starting to move the secondary sooner like a low gear. Cheers Don. |
08-30-2012, 07:51 PM | #3 |
Not Yet Wild
Join Date: Jun 2011
Posts: 15
|
Re: Clutch work?
Greetings Don.
I asked the same question here awhile back and was told that even though the clutches and principles are the same, there is no adjustment for belt to sheave on these clutches. No ABC clutch bolt for these I guess. I was quite concerned with the amount of slop in my EZ GO belt. P.S. I think I recognize your name from a sled forum, you got a 3-4' dump of snow in a weekend last year or year before if I remember correctly? |
09-03-2012, 07:54 AM | #4 | |
Not Yet Wild
Join Date: Aug 2012
Posts: 57
|
Re: Clutch work?
Quote:
Man pulled this clutch off what a yard sale! This this is warn right the he!! out. All three rollers are shot, the inner bushing of movable sheave is toast the cover bushing is shot. Sheaves are grooved out. Just a mess. There is no shims under the spider at all. If I can get a roller kit for the spider I might pull this apart and mess with it as a second clutch. I would mill about .125" off the main shaft so I can move the movable in and tighten up the belt to sheave. This would add much more low gear and move top end to the shift of the weights. Makes me sick every time I see huge belt to sheave..... waste of performance every time. Interesting how these clutches have a ton of tip weight. Same thing I have seen the Arctic cats respond very well to. I need a new comet clutch for this ride. Anyone know the taper for the 88? Cheers Don. |
|
09-03-2012, 08:57 AM | #5 |
Not Yet Wild
Join Date: Jun 2011
Posts: 15
|
Re: Clutch work?
Yard sale, tell me about it. This is what I stepped in when I bought my 2000 TXT. I wondered why the cart engaged so abruptly, cause it wasn't fully disengaging!
|
09-03-2012, 09:03 AM | #6 |
Not Yet Wild
Join Date: Jun 2011
Posts: 15
|
Re: Clutch work?
I've since put two new clutches on it from golfcartking I believe, half the cost of GC Duke here in ON. Cart runs like a dream now, but like you said, it'd be nice to address the belt to sheave issue. I remember reading your posts about this issue on the sled forum and realizing that it's critical for performance. I ended up buying the ABC bolt for my M8, feels much better.
|
09-03-2012, 02:33 PM | #7 | |
Not Yet Wild
Join Date: Aug 2012
Posts: 57
|
Re: Clutch work?
Quote:
WOW dude that secondary must have smoked a rock or something Eh? I think I am in for a new primary. I have the secondary all cleaned up with a ACat red secondary spring and 1/4 turn. Great back shift but not to much. Cheers Don. |
|
09-03-2012, 05:28 PM | #8 |
Not Yet Wild
Join Date: Jun 2011
Posts: 15
|
Re: Clutch work?
What are the compression numbers on a stock EZGO spring versus the Cat spring, they seem a little on the weaker side.
My secondary was so packed full of mud and corrosion I couldn't get it apart. Ran it till it seized up, I already had the new one to put on, destroyed it in the process of disassembly. Previous owner must have had a lot of fun in the mud, took me hours to clean every nook and cranny of mud and grass. |
09-04-2012, 12:25 PM | #9 | |
Not Yet Wild
Join Date: Aug 2012
Posts: 57
|
Re: Clutch work?
Quote:
Do you remember Erlandson? They did allot of sled clutching. They sell a clutch kit for these carts. I picked up the 30#-80# primary spring to go with the cat red secondary spring. Should work quite well. http://www.erlandsontechnology.com/D...rt_p/dsez2.htm After I fix this yard sale of a primary. There is three roll pins that you have to punch into the center of the spider to be able to turn the spider off. Reverse threads and she spins right off. I guess these pins are why there is no spider shims or adjustment as well as coarse threads. Going to mill the belt to sheave then red lock tight the spider back on. IF I can find rollers an pins for the spider. They are all shot and the inner and outer bushing for the movable sheave is toast too. Have to touch up the weights nothing to big of a deal. Just weld in some notches warn into the tip then grind off smooth again. I will post a picture of the how warn the parts are in here later tonight if I get a second. Cheers Don. |
|
09-04-2012, 01:09 PM | #10 |
Gone Wild
Join Date: Jul 2008
Location: Reddick IL
Posts: 11,220
|
Re: Clutch work?
A quick question, does your drive start to close at very low rpm?
My Yamaha starts to close at starting rpm and the belt clearance seems engineered in to allow the engine to fire before loading it. |
Tags |
spider shim? |
|
|
Similar Threads | ||||
Thread | Forum | |||
Clutch work CC ds 01 | Gas Club Car | |||
Will cw clutch work on ccw engine.. | Clone Engine Swaps | |||
Will It Work? | Gas Club Car | |||
Have to warn people on Precedents wanting driven clutch work done.. | Gas Club Car | |||
Would this clutch work in my G2 | Gas Yamaha |