|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
06-27-2016, 01:18 PM | #11 | |
Not Yet Wild
Join Date: Apr 2016
Posts: 55
|
Re: Photo of 96 GXT-804D Motor area?
Quote:
|
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-21-2016, 02:56 PM | #12 |
Not Yet Wild
Join Date: Apr 2016
Posts: 55
|
Re: Photo of 96 GXT-804D Motor area?
Anybody have a wiring diagram for this thing? I just got my coil in and wanna make sure everything is in order.
Also am I calling this thing right? Gxt 804d? I can't really find too much info on the web about it. |
07-21-2016, 09:38 PM | #13 |
Not Yet Wild
Join Date: Apr 2016
Posts: 55
|
Re: Photo of 96 GXT-804D Motor area?
Bump.
Can anyone tell me where the coil mounts to? |
08-02-2016, 12:45 AM | #14 |
Not Yet Wild
Join Date: Apr 2016
Posts: 55
|
Re: Photo of 96 GXT-804D Motor area?
Update: I put the coil in, changed the fuel lines, new pump. I was able to drive it around if I hold the choke closed. Not sure what its called but the plate in the carburetor that closes when the choke is pulled. The choke cable is pretty rusted and doesn't do much. Drove it around for about a minute and then the top, (valve cover?) started leaking oil. You can see that someone put that orange gasket sealer on it. Looks like they either lost a bolt or broke it off because that corner is where it is leaking oil.
|
08-02-2016, 06:11 AM | #15 |
Gone Wild
Join Date: Feb 2008
Location: Brooklyn, Michigan "Home of M.I.S."
Posts: 3,667
|
Re: Photo of 96 GXT-804D Motor area?
Sounds like you're on the way, might need to clean the carburetor and the valve cover takes an O ring (no gasket), hope the bolt isn't broke.
|
05-26-2017, 07:40 PM | #16 |
Not Yet Wild
Join Date: Apr 2016
Posts: 55
|
Re: Photo of 96 GXT-804D Motor area?
Good news! I swapped motors out and after some troubleshooting I got it working. It would only sputter when I used starting fluid. I adjusted the valves, tried with the exaust off, checked spark and ground, and still same. Finally took the float apart cleaned it and now its running. Still need a few things to make it solid before I take everything apart and repaint it.
|
05-26-2017, 07:49 PM | #17 |
Not Yet Wild
Join Date: Apr 2016
Posts: 55
|
Re: Photo of 96 GXT-804D Motor area?
So since i've been running it there has been some smoke from the exaust manifold and where the muffler connects. Not blue or coming out of the tail pipe. Any thoughts?
Its the old muffler from the old motor and there is a little oil where it connects to the frame on the bottom but not much elsewhere. |
09-30-2019, 11:06 PM | #18 |
Not Yet Wild
Join Date: Aug 2013
Posts: 20
|
Re: Photo of 96 GXT-804D Motor area?
adjust the valves
|
|
|
Similar Threads | ||||
Thread | Forum | |||
GXT 804D Key Start change back to PEDAL | Gas EZGO | |||
GXT 804D belt | Gas EZGO | |||
GXT 804D accessory harness Mystery wire | Gas EZGO | |||
knock noise from motor/axle area 95cc | Electric Club Car | |||
1997 gxt-804d | Gas EZGO |