244 robins cylinder nut torque

Hardatwork · 06-12-2011, 01:26 PM

I think the cylinder nut torque is 24 to 28 Ft.lbs on my 244 robins.
How do you torque them? Do you use crow foot adapters? If so does that change the reading on the torque wrench?

Thanks

Chuck

Hardatwork · 06-13-2011, 05:50 AM

OK I will ask this this question this way. Those that have put new top ends on your 244 robins how did you torque the jug.

Chuck

madoc1 · 06-13-2011, 07:29 AM

no i didn't. i think i can "feel" about the right amount to do it. just do it in a criss cross pattern, about a quarter turn past snug. you will feel it stop.

Dave Box · 06-13-2011, 07:43 AM

I nail my colors to the Madoc1 mast as well. I then rechecked the cylinder bolts and the head bolts after 10 hours (which I counted using my handy dandy rev counter).

Dave

Hardatwork · 06-13-2011, 08:09 AM

Thanks madok1 and Dave. Did you use any sealer on the gasket?

Chuck

madoc1 · 06-13-2011, 09:44 AM

no, but i guess a little non-hardening permatex wouldn't hurt anything.

06-12-2011, 01:26 PM	#1
Hardatwork Gone Wild Join Date: Dec 2010 Location: Iowa Posts: 179	244 robins cylinder nut torque I think the cylinder nut torque is 24 to 28 Ft.lbs on my 244 robins. How do you torque them? Do you use crow foot adapters? If so does that change the reading on the torque wrench? Thanks Chuck

06-13-2011, 05:50 AM	#2
Hardatwork Gone Wild Join Date: Dec 2010 Location: Iowa Posts: 179	Re: 244 robins cylinder nut torque OK I will ask this this question this way. Those that have put new top ends on your 244 robins how did you torque the jug. Chuck

06-13-2011, 07:29 AM	#3
madoc1 no clue Join Date: Sep 2009 Location: spicewood, texas Posts: 3,308	Re: 244 robins cylinder nut torque no i didn't. i think i can "feel" about the right amount to do it. just do it in a criss cross pattern, about a quarter turn past snug. you will feel it stop.

06-13-2011, 07:43 AM	#4
Dave Box Respect the Cart Join Date: May 2010 Location: Rocky Mount, Virginia Posts: 2,190	Re: 244 robins cylinder nut torque I nail my colors to the Madoc1 mast as well. I then rechecked the cylinder bolts and the head bolts after 10 hours (which I counted using my handy dandy rev counter). Dave

06-13-2011, 08:09 AM	#5
Hardatwork Gone Wild Join Date: Dec 2010 Location: Iowa Posts: 179	Re: 244 robins cylinder nut torque Thanks madok1 and Dave. Did you use any sealer on the gasket? Chuck

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

06-13-2011, 09:44 AM	#6
madoc1 no clue Join Date: Sep 2009 Location: spicewood, texas Posts: 3,308	Re: 244 robins cylinder nut torque no, but i guess a little non-hardening permatex wouldn't hurt anything.

Similar Threads
Thread	Forum
Robins MCI Engine	Gas EZGO
Torque on Cylinder Head Bolts??	Gas Yamaha
88 ezgo robins 244 cc	Gas EZGO
Fe290 Cylinder head Torque	Gas Club Car
robins engine	Big Block Talk!