|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
01-18-2015, 10:47 AM | #41 | |
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: 89 EC25 3pg rebuild questions
Quote:
I get them lined up close by eye, then set it on the truing stand, brass-hammer it to dead-nuts. These singles are painless compared to the sled/PWC triples. I'm in the middle of taking a 650 twin Yam to 1010cc. Pin holes get welded up, redrilled farther out. Rod and piston height, cam chain, studs all have to be matched up. Re-sleeved for much bigger bore, cut, rotate & weld cam since the crank is being indexed to 90-degrees instead of 360 to smooth the vibes and power delivery. One we de-stroked to allow bigger bore and valves for a class-limit GNCC ATV racer. Wanna change jugs, but the pattern is different? |
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
01-18-2015, 06:38 PM | #42 |
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: 89 EC25 3pg rebuild questions
Scraped, scrubbed, baked, blasted, washed, and bearings installed.
(sounds like a better weekend than I've had in a long time) |
01-19-2015, 02:56 PM | #43 |
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: 89 EC25 3pg rebuild questions
Back in the day we used used to smack them on the floor then back on the truing stand, smack again and repeat. Harley's of course.
|
01-25-2015, 12:53 AM | #44 |
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: 89 EC25 3pg rebuild questions
Back to the front page, with a fresh bore job and crank rebuild :) No concrete was chipped in the creation of this pictorial.
|
01-27-2015, 06:53 PM | #45 |
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: 89 EC25 3pg rebuild questions
How much did it take on the bore?
|
01-27-2015, 07:39 PM | #46 |
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: 89 EC25 3pg rebuild questions
.020 cleaned it up.
|
01-27-2015, 09:02 PM | #47 |
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: 89 EC25 3pg rebuild questions
So what brand piston? I thought the re-pops were only .025 and .050.
|
01-28-2015, 11:11 AM | #48 |
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: 89 EC25 3pg rebuild questions
Attack of the Metric System. I'd substituted inch.
Oversizes are .25mm and .50mm, close to US .010 and .020 |
01-30-2015, 04:34 PM | #49 |
Getting Wild
Join Date: Dec 2014
Location: Northern Indiana
Posts: 92
|
Re: 89 EC25 3pg rebuild questions
My bad, the gears were not turning upstairs, that does happen sometimes.
|
02-01-2015, 10:48 PM | #50 |
Gone Wild
Join Date: Apr 2014
Location: Flint, MI, USA
Posts: 656
|
Re: 89 EC25 3pg rebuild questions
She's fresh!
Getting the port timing sorted. |
|
|
Similar Threads | ||||
Thread | Forum | |||
G2 rebuild questions | Gas Yamaha | |||
1989 3pg top end rebuild questions | Gas EZGO | |||
Few questions for G9 rebuild. | Gas Yamaha | |||
Bottom End Rebuild Robin EC25-2PG | Gas EZGO | |||
rebuild on 2pg 244 cc engine questions | Gas EZGO |