|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
12-31-2014, 02:35 PM | #11 |
Not Yet Wild
Join Date: Dec 2014
Posts: 13
|
Re: 92 ezgo wont go
I'm showing no voltage between m- and the blue wire
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-31-2014, 02:41 PM | #12 |
Not Yet Wild
Join Date: Dec 2014
Posts: 13
|
Re: 92 ezgo wont go
Ok my voltage isn't dropping so I checked across m- and the blue wire and read 0. So am I not getting power to my controller?
|
12-31-2014, 03:52 PM | #13 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 92 ezgo wont go
|
12-31-2014, 03:57 PM | #14 |
Not Yet Wild
Join Date: Dec 2014
Posts: 13
|
Re: 92 ezgo wont go
Ok sorry about that. Reading between the blue and b- I'm reading 38 volts
|
12-31-2014, 04:02 PM | #15 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 92 ezgo wont go
FWIW: The control element in the controller (about a dozen MOSFETs connected in parallel) is located between the B- and M- terminals.
The output to the motor is PWM (Pules Width Modulated) DC whose duty-cycle varies from 0% to 100% as directed by the throttle signal. When the duty cycle is 0%, the control element is effectively an open, so you measure the full pack voltage across it if the high current circuit is intact. When the duty cycle is 100%, the control element is effectively a short, so you measure zero volts across it unless there is a current flowing through the high current loop. (The MOSFETs drop about 0.05V to 0.10V per 100A of current flow through them, so the voltage in a working system will be slightly more than Zero) |
12-31-2014, 04:03 PM | #16 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 92 ezgo wont go
|
12-31-2014, 04:06 PM | #17 |
Not Yet Wild
Join Date: Dec 2014
Posts: 13
|
Re: 92 ezgo wont go
How do I check the throttle signal. Is that the black and white wires?
|
12-31-2014, 04:18 PM | #18 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 92 ezgo wont go
|
12-31-2014, 04:35 PM | #19 |
Not Yet Wild
Join Date: Dec 2014
Posts: 13
|
Re: 92 ezgo wont go
Pedal up i have close to 0 And with pedal down I have 5000
|
12-31-2014, 05:55 PM | #20 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 92 ezgo wont go
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
97' ezgo wont run | Gas EZGO | |||
Ezgo dcs solenoid clicks but wont disengage and wont move | Electric EZGO | |||
01 EZGO wont do nothing | Electric EZGO | |||
Help EZGO Wont go EZ | Electric EZGO | |||
94 EZGO wont go | Electric EZGO |