|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
05-24-2015, 08:19 AM
|
#111 |
|
Not Yet Wild
Join Date: May 2015
Location: Upstate NY
Posts: 17
|
Re: Installing HEI Ignition on 3PG Carts
Thanks for the info guys... Sounds like you might have nailed it right on the head. Long story short, I cobbed mounting it with self tappers in the same location as the stock one and noticed it was a little loose when I got it back in the garage. If it's that finicky, I think I'll explore remounting it elsewhere where it has a thicker heat sink.. 1989, I'm in glen, just outside fultonville. How bout you? Thanks for the info, I'll keep you updated
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
05-24-2015, 08:22 AM
|
#112 |
|
Not Yet Wild
Join Date: May 2015
Location: Upstate NY
Posts: 17
|
Re: Installing HEI Ignition on 3PG Carts
Oh, and I just switched to a ngk bp4hs at .032
|
|
|
|
|
05-24-2015, 09:33 AM
|
#113 | |
|
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: Installing HEI Ignition on 3PG Carts
Quote:
I'm at the south end of Canandaigua Lake. |
|
|
|
|
|
05-25-2015, 07:50 PM
|
#114 |
|
Not Yet Wild
Join Date: May 2015
Location: Upstate NY
Posts: 17
|
Re: Installing HEI Ignition on 3PG Carts
Ok, I'm at a loss now... Replaced the ignition control module and still have no spark. Rechecked the pulsar coil at 146 ohms, and the coil at .7ohms. I've got 12v on the yellow wire going to the module, and the green wire at the coil. Good continuity to ground at the coil mount, and the ignition module, and good continuity on the orange from the module to the coil. New spark plug wire is reading 3730 ohms (18" wire). Any ideas of what I might be missing or ways to check the ignition control module for function? Thanks in advance
|
|
|
|
|
05-25-2015, 07:58 PM
|
#115 |
|
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: Installing HEI Ignition on 3PG Carts
If you can, post a pic of your setup.
|
|
|
|
|
05-25-2015, 08:10 PM
|
#116 |
|
Not Yet Wild
Join Date: May 2015
Location: Upstate NY
Posts: 17
|
Re: Installing HEI Ignition on 3PG Carts
Have it mounted to a piece of aluminum now as a heat sink
|
|
|
|
|
05-25-2015, 08:11 PM
|
#117 |
|
Not Yet Wild
Join Date: May 2015
Location: Upstate NY
Posts: 17
|
Re: Installing HEI Ignition on 3PG Carts
Coil
|
|
|
|
|
05-25-2015, 08:17 PM
|
#118 |
|
Gone Wild
Join Date: Oct 2010
Posts: 6,730
|
Re: Installing HEI Ignition on 3PG Carts
What is the resistance from the cylinder head to battery negative?
Also, you will likely have to swap the red and blue wires coming from the pulser. |
|
|
|
|
05-25-2015, 08:20 PM
|
#119 |
|
Not Yet Wild
Join Date: May 2015
Location: Upstate NY
Posts: 17
|
Re: Installing HEI Ignition on 3PG Carts
.3 ohms
|
|
|
|
|
05-25-2015, 08:22 PM
|
#120 |
|
Not Yet Wild
Join Date: May 2015
Location: Upstate NY
Posts: 17
|
Re: Installing HEI Ignition on 3PG Carts
And yes, they are switched at the pulsar connector.
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Top Notch Carts, Edinburgh, Indiana. Carts I've built. | Members Rides | |||
| Yamaha G9-Ignition Coil & Ignition Switch-Help | Gas Yamaha | |||
| Installing a DCX 400 | Electric EZGO | |||
| Carts, carts, carts!!!-'01 EZ GO-$1300.00!!?? | Golf Carts and Parts | |||
| Installing Light Kit G16 | Gas Yamaha | |||
Linear Mode
