13hp clone

cclingma · 05-06-2008, 05:08 PM

I've enjoyed reading several post on this and other sites about clone installs but this one really has my attention. I'm starting to see how people get hooked on reality TV as I have to check this everyday to see what's happened. Please keep us posted.

Are you using all the factory linkage for throttle?

GA.NUT · 05-07-2008, 11:20 AM

Im Looking For A Morse Cable To Hook To The Peddle And Thorotle.like Used On Boats Cause Its Good And Stout.

Shmitty · 05-10-2008, 12:03 PM

Ok guys... I'm struggling to find a belt for this clone motor! Someone out there has to know of something that I can use. I've tried and tried to find something that will work.

Help guys!!! I wanna be rolling... Thought I would have it done this weekend!

What did you other clone guys use?

4x4 CC · 05-10-2008, 07:50 PM

I learned that you either gotta use the stock belt or switch to a a 1 3/16" belt if you cant.

Shmitty · 05-10-2008, 09:13 PM

Well unfortunately I can't use the stock belt since I had to move the motor up two inches. So technically I need a 4" longer belt. That I can't find. . .

What about the other Clone guys... What have you been using?

Shmitty · 05-13-2008, 06:46 PM

Looks like I'm going to have to go to a 1 3/16 " X41 and make a new mounting bracket for the motor.

4x4 CC · 05-13-2008, 08:49 PM

Good Choice...

PV5 · 05-13-2008, 09:08 PM

If you have to make a new motor mount try to slot your mounting holes.
This will give you a little adjustment on your belt length.
1 3/16 X 41 is what I'm running.
I used a cloth tape measure to get my length. lay tm down inside the drive or front clutch on the shaft, go around the outside edge of the driven or rear clutch and get your length.

This worked for me....just my 2 cents,
Bryan

Shmitty · 05-13-2008, 09:22 PM

Awesome!!!

Thanks for the input. How is the motor working out for you? Anything else I should know? I'm pretty close to getting it done. . . FINALLY!

GA.NUT · 05-14-2008, 09:47 AM

Shmitty I Am Going To Have To Use 1 3/16 Belt Im Using The Stock C/c Belt Now But Its To Tight And Wont Shift In And Out Of Gear Without Grinding And When I Start It In Gear I Have To Have The Brake On .my Monting Plate Will Move Forward Enough I Wont Have To Drill New Holes Again.[i Hope]

05-06-2008, 05:08 PM	#51
cclingma Getting Wild Join Date: Jan 2008 Posts: 147	Re: 13hp clone I've enjoyed reading several post on this and other sites about clone installs but this one really has my attention. I'm starting to see how people get hooked on reality TV as I have to check this everyday to see what's happened. Please keep us posted. Are you using all the factory linkage for throttle?
cclingma Getting Wild Join Date: Jan 2008 Posts: 147

05-07-2008, 11:20 AM	#52
GA.NUT Not Yet Wild Join Date: Mar 2008 Location: S. GA Posts: 65	Re: 13hp clone Im Looking For A Morse Cable To Hook To The Peddle And Thorotle.like Used On Boats Cause Its Good And Stout.

05-10-2008, 12:03 PM	#53
Shmitty Not Yet Wild Join Date: Mar 2008 Posts: 34	Re: 13hp clone Ok guys... I'm struggling to find a belt for this clone motor! Someone out there has to know of something that I can use. I've tried and tried to find something that will work. Help guys!!! I wanna be rolling... Thought I would have it done this weekend! What did you other clone guys use?
Shmitty Not Yet Wild Join Date: Mar 2008 Posts: 34

05-10-2008, 07:50 PM	#54
4x4 CC Frog Hunter Join Date: Dec 2006 Location: Little Rock, Ar Posts: 1,161	Re: 13hp clone I learned that you either gotta use the stock belt or switch to a a 1 3/16" belt if you cant.

05-10-2008, 09:13 PM	#55
Shmitty Not Yet Wild Join Date: Mar 2008 Posts: 34	Re: 13hp clone Well unfortunately I can't use the stock belt since I had to move the motor up two inches. So technically I need a 4" longer belt. That I can't find. . . What about the other Clone guys... What have you been using?
Shmitty Not Yet Wild Join Date: Mar 2008 Posts: 34

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

05-13-2008, 06:46 PM	#56
Shmitty Not Yet Wild Join Date: Mar 2008 Posts: 34	Re: 13hp clone Looks like I'm going to have to go to a 1 3/16 " X41 and make a new mounting bracket for the motor.
Shmitty Not Yet Wild Join Date: Mar 2008 Posts: 34

05-13-2008, 08:49 PM	#57
4x4 CC Frog Hunter Join Date: Dec 2006 Location: Little Rock, Ar Posts: 1,161	Re: 13hp clone Good Choice...

05-13-2008, 09:08 PM	#58
PV5 Gone Wild Join Date: Aug 2007 Location: Jerusalem AR Posts: 214	Re: 13hp clone If you have to make a new motor mount try to slot your mounting holes. This will give you a little adjustment on your belt length. 1 3/16 X 41 is what I'm running. I used a cloth tape measure to get my length. lay tm down inside the drive or front clutch on the shaft, go around the outside edge of the driven or rear clutch and get your length. This worked for me....just my 2 cents, Bryan

05-13-2008, 09:22 PM	#59
Shmitty Not Yet Wild Join Date: Mar 2008 Posts: 34	Re: 13hp clone Awesome!!! Thanks for the input. How is the motor working out for you? Anything else I should know? I'm pretty close to getting it done. . . FINALLY!
Shmitty Not Yet Wild Join Date: Mar 2008 Posts: 34

05-14-2008, 09:47 AM	#60
GA.NUT Not Yet Wild Join Date: Mar 2008 Location: S. GA Posts: 65	Re: 13hp clone Shmitty I Am Going To Have To Use 1 3/16 Belt Im Using The Stock C/c Belt Now But Its To Tight And Wont Shift In And Out Of Gear Without Grinding And When I Start It In Gear I Have To Have The Brake On .my Monting Plate Will Move Forward Enough I Wont Have To Drill New Holes Again.[i Hope]

Similar Threads
Thread	Forum
13HP came in one piece	Big Block Talk!
Having some fun with 13hp	Videos
13hp Club Car Swap	Big Block Talk!
My 13hp engine update	Big Block Talk!