|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
10-26-2020, 04:27 PM | #1 |
Not Yet Wild
Join Date: Sep 2020
Posts: 11
|
Mzj 400a solenoid install On G29
Trying to install a mzj 400a solenoid. However, the holes do not line up with the stock bolt location on my 2012 G29. What is the easiest way to install the solenoid? I believe I may be able to remove the stock solenoid holder and reuse but I’m not sure. Can I easily drill through the solenoid mounting plate or the stock mounting area and replace with nuts and bolts?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-27-2020, 11:36 AM | #2 | |
Not Yet Wild
Join Date: Jun 2020
Posts: 22
|
Re: Mzj 400a solenoid install On G29
Quote:
|
|
10-27-2020, 12:39 PM | #3 |
Not Yet Wild
Join Date: Jun 2020
Location: WI
Posts: 32
|
Re: Mzj 400a solenoid install On G29
Just shift it over and use some self tapping screws. I ran into the same issue when installing a Riot kit and this was the easy solution.
https://www.buggiesgonewild.com/showthread.php?t=166988 |
10-27-2020, 02:28 PM | #4 |
Not Yet Wild
Join Date: Sep 2020
Posts: 11
|
Re: Mzj 400a solenoid install On G29
So I installed the solenoid and have no power. Used a 3 amp diode as told and had the cart in tow mode while making the swap. I have pack power on the 2 large terminals but nothing on the small terminals. What do you guys think it could be? I reinstalled the old solenoid and get the same results there.
|
10-27-2020, 04:13 PM | #5 |
Not Yet Wild
Join Date: Sep 2020
Posts: 11
|
Re: Mzj 400a solenoid install On G29
After reading some of the posts on here I tried to push the cart with the run switch on and the key on with no click in the solenoid. Based on other posts does it sound like a bad controller? I did slightly tweak the post that the cable that runs from the controller to the solenoid is connected to on the controller, but I didn’t think I hurt anything. Thoughts?
|
10-27-2020, 08:26 PM | #6 |
Not Yet Wild
Join Date: Sep 2020
Posts: 11
|
Re: Mzj 400a solenoid install On G29
Something else I just thought about....I installed the 400a solenoid with the stock controller. Could this have burned up the controller and be the whole issue?
|
10-28-2020, 10:35 AM | #7 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Mzj 400a solenoid install On G29
The small terminals should have B+ when the tow/run switch Is on. Then one will have B- when the solenoid is supposed to be on. I would remove the diode for now, for testing. If you installed the diode backwards, you could have caused damage.
|
10-28-2020, 01:46 PM | #8 |
Not Yet Wild
Join Date: Sep 2020
Posts: 11
|
Re: Mzj 400a solenoid install On G29
Does the positive side of the diode go to the tow/run switch or to the controller side of the small terminal?
|
10-28-2020, 02:20 PM | #9 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Mzj 400a solenoid install On G29
It goes towards the + wire which ever side you put that on.
|
10-28-2020, 04:17 PM | #10 |
Not Yet Wild
Join Date: Jun 2020
Posts: 22
|
Re: Mzj 400a solenoid install On G29
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Mock Install: Alltrax SR48500 Controller, 400a Solenoid, SW202 Reversing Contactor | Electric EZGO | |||
MZJ-400A Solenoid install issues | Electric Club Car | |||
EZGO PDS - New ALLTRAX XCT48500 and 400a solenoid install. no light - newbie | Electric EZGO | |||
ScottyB Alltrax 500,wires,400A &202 install | Electric EZGO | |||
Alltrax Controller and 400a Solenoid Install Help | Electric Club Car |