G9 won't pull and cuts out sometimes

RAZOR · 09-17-2008, 11:08 AM

Replaced the plugs, air filter, and its getting plenty of fuel. I can smell gas before it cuts out but don't see anything on bowl of carburator. Sprayed it out with cleaner and no change. Seems to loss power when wide open and pops sometimes. Won't pull for crap up a hill either.

spriddle · 09-17-2008, 01:45 PM

Check for air leaks around the air filter box: should be completely sealed. Also look at the spacer between the carb. and intake. Check your throttle cables to make sure they are adjusted so the carb. throttle completely opens and closes.

Pulling problem: Check your front motor mounts for wear for the pulling problem. Could be a bad clutch, rear clutch spring, or missing clip on the drive shaft on rearend.

RAZOR · 09-18-2008, 08:22 AM

I'll check it out.

TheNewGuy · 09-18-2008, 09:27 AM

Big Block!!!

sabercat · 09-19-2008, 02:41 PM

hey new guy were did you get the fender flares for your g9, i can't seem to find any for mine

TheNewGuy · 09-22-2008, 07:51 AM

Quote:

Originally Posted by sabercat

hey new guy were did you get the fender flares for your g9, i can't seem to find any for mine

Got them from JC Whitney. I used the surface mount style. > http://www.jcwhitney.com/EASY-TO-TRI...3139_10614.jcw

RAZOR · 11-11-2008, 05:42 PM

Seems I never checked back in. Cart is running stout now. Thanks guys. Needed a good tuneup and kick in the @$$!

sabercat · 11-13-2008, 04:07 PM

hey ron, did you just order 2 sets of 2 and were they long enough, and are they bent to go around the wheel well or are they like a diy thing??

TheNewGuy · 11-13-2008, 07:33 PM

1 pair did it all. It's flexible rubber so you can bend it and screw it into place. For tight bends cut a triangle out of the inside flange using tin snips. If you want it to look right, you have to cut the wheel opening flange off of the body, front and rear.

If you get them keep us posted with pics!

sabercat · 11-14-2008, 06:38 AM

ok, but how far did it stick out compared to the stock body flares, when you replace them with theses other ones

09-17-2008, 11:08 AM	#1
RAZOR Gone Wild Join Date: Sep 2008 Location: pending Posts: 352	G9 won't pull and cuts out sometimes Replaced the plugs, air filter, and its getting plenty of fuel. I can smell gas before it cuts out but don't see anything on bowl of carburator. Sprayed it out with cleaner and no change. Seems to loss power when wide open and pops sometimes. Won't pull for crap up a hill either.

09-17-2008, 01:45 PM	#2
spriddle Admin Join Date: Dec 2006 Location: TN Posts: 101,858	Re: G9 won't pull and cuts out sometimes Check for air leaks around the air filter box: should be completely sealed. Also look at the spacer between the carb. and intake. Check your throttle cables to make sure they are adjusted so the carb. throttle completely opens and closes. Pulling problem: Check your front motor mounts for wear for the pulling problem. Could be a bad clutch, rear clutch spring, or missing clip on the drive shaft on rearend.

09-18-2008, 08:22 AM	#3
RAZOR Gone Wild Join Date: Sep 2008 Location: pending Posts: 352	Re: G9 won't pull and cuts out sometimes I'll check it out.

09-18-2008, 09:27 AM	#4
TheNewGuy Admin/Moderator Join Date: Dec 2006 Location: Ohio Posts: 18,047	Re: G9 won't pull and cuts out sometimes Big Block!!!
	Ron PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project

09-19-2008, 02:41 PM	#5
sabercat gone yamaha! Join Date: Sep 2008 Location: ontario, canada Posts: 1,424	Re: G9 won't pull and cuts out sometimes hey new guy were did you get the fender flares for your g9, i can't seem to find any for mine

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

11-11-2008, 05:42 PM	#7
RAZOR Gone Wild Join Date: Sep 2008 Location: pending Posts: 352	Re: G9 won't pull and cuts out sometimes Seems I never checked back in. Cart is running stout now. Thanks guys. Needed a good tuneup and kick in the @$$!

11-13-2008, 04:07 PM	#8
sabercat gone yamaha! Join Date: Sep 2008 Location: ontario, canada Posts: 1,424	Re: G9 won't pull and cuts out sometimes hey ron, did you just order 2 sets of 2 and were they long enough, and are they bent to go around the wheel well or are they like a diy thing??

11-13-2008, 07:33 PM	#9
TheNewGuy Admin/Moderator Join Date: Dec 2006 Location: Ohio Posts: 18,047	Re: G9 won't pull and cuts out sometimes 1 pair did it all. It's flexible rubber so you can bend it and screw it into place. For tight bends cut a triangle out of the inside flange using tin snips. If you want it to look right, you have to cut the wheel opening flange off of the body, front and rear. If you get them keep us posted with pics!
	Ron PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project

11-14-2008, 06:38 AM	#10
sabercat gone yamaha! Join Date: Sep 2008 Location: ontario, canada Posts: 1,424	Re: G9 won't pull and cuts out sometimes ok, but how far did it stick out compared to the stock body flares, when you replace them with theses other ones

Similar Threads
Thread	Forum
91 Ez GO CUTS OUT AT 3/4 THROTTLE	Electric EZGO
Charger cuts off after 5 mins?	Electric Club Car
Help !!!!!!! 36v Ezgo Won't Pull	Electric EZGO
what is the most i could pull	Gas EZGO