|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
10-02-2009, 03:51 PM | #1 |
Not Yet Wild
Join Date: Jun 2009
Location: Spartanburg, SC
Posts: 58
|
EZGO 3 Position Key Switch Wiring diagram
Stuck on wiring new switch w/ lights. On the back of switch are the terminals
L I B1 D or B Can't tell Need a wiring diagram for this switch Thanks in advance for the help, Bryan |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-02-2009, 04:54 PM | #2 |
Not Yet Wild
Join Date: Apr 2009
Posts: 29
|
Re: EZGO 3 Position Key Switch Wiring diagram
Hi Bryan,
How about an ultra crude hand-made diagram.. Good luck with the install. fbm |
03-30-2014, 08:57 AM | #3 |
Not Yet Wild
Join Date: Oct 2013
Posts: 4
|
Re: EZGO 3 Position Key Switch Wiring diagram
can you repost wiring diagram of what letters attach to I guess you crude diagram
thanks |
03-30-2014, 09:51 AM | #4 |
Stay thirsty my friends!
Join Date: Jan 2007
Location: Suburban Chicago
Posts: 24,291
|
Re: EZGO 3 Position Key Switch Wiring diagram
You can sort this out with a common multimeter set to the OHMS scale. Turn the key to the first notch and start touching the multimeter probes to the switch terminals. As soon as you get a reading, those two terminals are for the solenoid control circuit wires you removed from the old switch. Polarity is not an issue as the switch is simply a make/break unit. The other two terminals would be used for the light circuit and will show a reading only when the switch is keyed to the second position.
|
03-30-2014, 02:15 PM | #5 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: EZGO 3 Position Key Switch Wiring diagram
Assuming it's for an EZ-Go, the two switches are independent. Make sure they are, as one is for 36 or 48 volt and the other is for 12 volt. Not that it won't work, but easiest to keep them separate, or polarity will become important.
|
03-30-2014, 08:18 PM | #6 |
Not Yet Wild
Join Date: Mar 2014
Posts: 2
|
Re: EZGO 3 Position Key Switch Wiring diagram
|
03-31-2014, 06:30 AM | #7 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: EZGO 3 Position Key Switch Wiring diagram
To add to my post above, if the switches are not independent, which they probably are with four poles, polarity and potential are both important. If you're tapping two batteries for 12 volts, the pack negative (or positive) has to be the same for the pack as for the 12 volts. If your using a reducer, it needs to have a "remote" wire, that activates it by 36 or 48 volts, but not a power wire, if that makes sense. Power to a reducer can exceed the switch rating.
|
03-31-2014, 09:44 AM | #8 | |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: EZGO 3 Position Key Switch Wiring diagram
Quote:
Welcome to BGW |
|
09-29-2016, 07:16 PM | #9 |
Not Yet Wild
Join Date: Sep 2016
Location: Georgia
Posts: 3
|
Re: EZGO 3 Position Key Switch Wiring diagram
I need some help if you don't mind. I have a 2001 Workhorse 800 gas and when I got it all the wires were disconnected from the key switch. The list of wires and their connections are :
Red-fuel gauge Green-gas pedal Blue-solenoid Blue/white stripe-unknown Blue/white stripe-also unknown I cannot figure out the proper connections. I would greatly appreciate any guidance. |
09-30-2016, 06:27 AM | #10 |
Card Carrying Old Fart
Join Date: Feb 2012
Location: Kentucky
Posts: 706
|
Re: EZGO 3 Position Key Switch Wiring diagram
I installed a similar switch on my cart. I don't think I had a wiring diagram either. The switch turns clockwise. Farthest left position is everthing off. Turn the key to the second position. This is for cart power on. Using a volt meter check each terminal for continuity between two terminals. Those will be for cart power (36v or 48v). The other two will be for lights 12v in and 12v out. Turn the key to the far right position and check for continuity with those. BTW, I wired my lights directly from two center batteries (both the pos and neg)in the pack and used an inline fuse.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
EZGO Electric 3 position key switch #2670 | Electric EZGO | |||
F/R switch detail wiring diagram,36 V Club Car 90's | Electric Club Car | |||
Wiring Diagram Key Switch-86 Columbia Gas | Gas Columbia ParCar | |||
F&R switch wiring diagram ? | Electric Club Car | |||
wiring position on 36 volt motor q. | Electric Club Car |