|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
08-09-2015, 03:25 PM | #1 |
Not Yet Wild
Join Date: May 2010
Posts: 55
|
Need help with a G29. Dead
Cart was running fine. I installed a winch today and got everything tightened and ready. I finished by attached pos terminal to main battery pack followed by flipping to run. Everything came on. I hit the remote for the winch to release the cable and go out. Instead it was reversed so I turned the power off and pulled the cable out a bit so I could roll it back in. At this point I had no power to the key or winch. I disconnected the winch and still no power to the key. I have power at batteries then working backwards I have power at solenoid but no power on the side of the solenoid by the controller. What else can I check since the power stops at solenoid? What does the 2 small wires connect to from the solenoid.
I have a Alltrax 500 xvt controller and DD motor. Plowmans I havent had problems until I hooked the winch up. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-09-2015, 03:51 PM | #2 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Need help with a G29. Dead
Where did you connect every wire from winch, how many wires were there?
|
08-09-2015, 04:05 PM | #3 | |
Not Yet Wild
Join Date: May 2010
Posts: 55
|
Re: Need help with a G29. Dead
Quote:
What does the 2 little wires go to from the solenoid? Should I have power on both sides of solenoid with key on and in run postion? Seems like thats where Im I've lost power. Winch is completely unhooked for now while trouble shooting. |
|
08-09-2015, 04:55 PM | #4 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Need help with a G29. Dead
I am not sure about the wiring of the winch, no idea what model ect it is, so i am going to focus on getting the cart running again. What year is your cart? Was it equipped with lights from the factory? There is one or more fuses in the cart wiring harness. One is under the rear access cover. The others are usually in the harness on one of the uprights that the rain tubes run down.
|
08-09-2015, 05:21 PM | #5 | |
Not Yet Wild
Join Date: May 2010
Posts: 55
|
Re: Need help with a G29. Dead
Quote:
Does the key wiring have a fuse in between solenoid and key? I have the old stock solenoid that I took off when I did the controller/motor upgrade. |
|
08-09-2015, 05:35 PM | #6 | |
Not Yet Wild
Join Date: May 2010
Posts: 55
|
Re: Need help with a G29. Dead
Quote:
|
|
08-09-2015, 07:05 PM | #7 | |
Not Yet Wild
Join Date: May 2010
Posts: 55
|
Re: Need help with a G29. Dead
Quote:
Winch is a Vipor 2500 elite. Thanks for the reply cgtech. I appreciate all the help you give to us newbies. |
|
08-10-2015, 10:26 AM | #8 |
Not Yet Wild
Join Date: May 2010
Posts: 55
|
Re: Need help with a G29. Dead
Since my winch is blowing my 3amp fuse when connected to the key. What should I do? Use a 15amp fuse or connect to battery with a kill switch and fuse?
|
08-10-2015, 01:09 PM | #9 |
Gone Wild
Join Date: May 2012
Location: Rio Verde, Az
Posts: 7,183
|
Re: Need help with a G29. Dead
Your winch needs WAY more then 3 amps! What voltage winch is it and how did you hook it up? It can't run off a 12V reducer either.
|
08-10-2015, 02:04 PM | #10 |
Not Yet Wild
Join Date: May 2010
Posts: 55
|
Re: Need help with a G29. Dead
Im running off of 2 8v batteries. I called Motoalliance(Viper winch) and the tech told me I need to connect the remote pos to the battery. I guess I need to add a fuse in line.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
The '92 G9 Dead again | Gas Yamaha | |||
EZ GO Dead | Electric EZGO | |||
Dead cart, possible dead Solenoid | Electric Club Car | |||
48v CC dead,everythings dead | Electric Club Car |