|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
12-15-2017, 11:48 PM | #1 |
Not Yet Wild
Join Date: Jun 2012
Location: Iowa
Posts: 59
|
G14a transmission
I just bought some high speed gears that were suppose to be for my G14A After finding they were not right I searched my service manuals and found that the G2 and G9 transmition look more like mine. Are the internal components interchange able?
1995 Ultima with a G14a drive train. engine and trany. Thanks guys. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-17-2017, 04:39 PM | #2 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G14a transmission
The gears for the Dana axle (late G14-G22) are not compatible with the early G14 and prior axle.
|
12-17-2017, 05:22 PM | #3 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,633
|
Re: G14a transmission
You will also find the tie rods and most other parts on the 95 g14 are from the G2 yamaha type carts where the 96 G14 uses the later G16 parts. Alas most suppliers don't seem aware of this aspect on the early 95 G14. P.S. I have one.
|
12-19-2017, 11:37 PM | #4 |
Not Yet Wild
Join Date: Jun 2012
Location: Iowa
Posts: 59
|
Re: G14a transmission
So that is why my service manual shows a G2-G9 transaxle. I have figured that all out. It appears as though the G2-G5-G8- and G9 all have the same trans axle as the part numbers for the ring gears, counter shaft and counter gear all match. I have sent back the gears and have found a supplier for the G2-G9 high speed gears. Just have to wait for them to make another run on them. Thanks raydhd, great info, I salute you sir.
|
12-20-2017, 09:54 AM | #5 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: G14a transmission
Make shure you get a new gasket. If the old one is damaged, it must be cleaned off and a new one installed for proper spacing.
|
12-20-2017, 05:35 PM | #6 |
Not Yet Wild
Join Date: Jun 2012
Location: Iowa
Posts: 59
|
Re: G14a transmission
Ok, I'm fairly sure I'm dealing with a stock G2 or G9 transaxle. The ring gear has 12 teeth spline and 76 out side. The counter gear has 13 teeth on the spline and 17 on out side gear. Can anyone say for sure this is stock ? Thanks again guys.
|
12-21-2017, 12:19 AM | #7 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G14a transmission
I can't confirm with total confidence. Those axles are so bullet-proof, I never have to go in there. Haven't been there enough to count the teeth. I think I have only opened up one or 2 ever.
|
12-21-2017, 08:54 AM | #8 |
Not Yet Wild
Join Date: Jun 2012
Location: Iowa
Posts: 59
|
Re: G14a transmission
Is the clearance really that critical to not be able to use RV sealer on the case?
|
12-21-2017, 09:21 AM | #9 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G14a transmission
|
12-21-2017, 09:34 AM | #10 |
Admin/Moderator
Join Date: Dec 2006
Location: Ohio
Posts: 18,047
|
Re: G14a transmission
|
Ron
PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
G14a won't start | Gas Yamaha | |||
Old Yamaha G14a is dying | Gas Yamaha | |||
CPP speed spring for G14A | Gas Yamaha | |||
g14a wont turnover | Gas Yamaha | |||
G14A Starter wiring | Gas Yamaha |