03-16-2014, 03:47 PM | #1 |
Not Yet Wild
Join Date: Mar 2014
Posts: 48
|
Clutch Removel
I have a 1991 club car and it needs a new crankcase gasket. I have taken part of the clutch off the shaft but I cant remove the part that that holds the starter belt. Any ideas of how? Thanks.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-16-2014, 06:50 PM | #2 |
Getting Wild
Join Date: Jan 2014
Location: Mechanicsville, VA
Posts: 77
|
Re: Clutch Removel
You need to use a clutch removal tool. It's a special bolt that threads into the crank and pops the clutch off.
|
03-16-2014, 07:02 PM | #3 |
Not Yet Wild
Join Date: Mar 2014
Posts: 48
|
Re: Clutch Removel
I did it split the clutch in half. Took it off removed retaining ring removed next piece and the one wall of the drive belt housing and the groove the starter belt goes is all thats left. I can't figure out how to remove it.
|
03-16-2014, 09:08 PM | #4 |
Call me Rich
Join Date: Mar 2011
Location: Western NY
Posts: 1,156
|
Re: Clutch Removel
You removed the outer half of the entire primary clutch/generator belt pulley. You need to buy the club car specific clutch puller to remove the whole thing. Look on ebay, they're about $30-35. The pic I'm posting is what you are looking at still mounted on your crank pulley, correct?
|
03-16-2014, 09:23 PM | #5 |
Not Yet Wild
Join Date: Mar 2014
Posts: 48
|
I also removed that piece. The next piece is my problem.
Sent from my iPod touch using Tapatalk |
03-16-2014, 09:36 PM | #6 |
I Refuse To Get Stuck!!!
Join Date: Jun 2010
Location: Hilton,NY
Posts: 5,427
|
Re: Clutch Removel
The part that is press-fit on the crankshaft requires the puller or you will ruin it trying to remove it.The only other way is to pump the retainer-bolt hole full of grease and reinstall the bolt,it will hydraulic it off,sometimes takes a few times adding grease and retightening to make it pop.Hope this helps.
|
03-16-2014, 09:37 PM | #7 |
Not Yet Wild
Join Date: Mar 2014
Posts: 48
|
Ok thanks
Sent from my iPod touch using Tapatalk |
03-16-2014, 09:41 PM | #8 |
Not Yet Wild
Join Date: Mar 2014
Posts: 48
|
Sent from my iPod touch using Tapatalk |
03-16-2014, 09:41 PM | #9 |
Not Yet Wild
Join Date: Mar 2014
Posts: 48
|
Sent from my iPod touch using Tapatalk |
03-17-2014, 06:41 AM | #10 |
Call me Rich
Join Date: Mar 2011
Location: Western NY
Posts: 1,156
|
Re: Clutch Removel
Yeah, see that shaft sticking out isnt the crankshaft, its part of the clutch. The actual crankshaft is only a couple inches and is tapered.
|
Tags |
club car 1991, clutch, crankcase |
|
|
Similar Threads | ||||
Thread | Forum | |||
Tips & Hints for installing Clutch Tuning Kit, Removal of Drive Clutch | Gas Club Car | |||
yamaha g16e axle removel ? | Electric Yamaha | |||
flywheel removel | Gas Yamaha | |||
spark plug wire removel | Gas Yamaha |