|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
11-06-2009, 07:37 AM | #1 |
Not Yet Wild
Join Date: Nov 2009
Posts: 4
|
EZ GO Workhorse runs, but does not move
I have a 1999 EZGO Workhorse, the motor runs, but will not move. I can raise the rear of the cart off the ground, and the wheels will turn, but when I put it back on the ground, nothing. The axles are good, the hubs are not stripped out, I took the differential apart and found nothing broken......Is it the clutch? Which one, the drive or driven, and how can I troubleshoot, instead of hanging unnecessary new parts?
Thanks! |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-06-2009, 08:30 AM | #2 |
Gone Crazy
Join Date: Jan 2007
Location: Chesterfield, Va
Posts: 6,021
|
Re: EZ GO Workhorse runs, but does not move
With the wheels on the ground start the cart, when you rev the motor do both clutches turn and it sits there?
|
11-06-2009, 08:40 AM | #3 |
Not Yet Wild
Join Date: Nov 2009
Posts: 4
|
Re: EZ GO Workhorse runs, but does not move
Yes, I start the cart, the rpms come up, both the drive clutch and driven clutch turn, the clutchs force their belts "up" the pulleys as if their trying to pull, but the cart does not move.
|
11-06-2009, 08:46 AM | #4 |
Love my Big Block
Join Date: Oct 2009
Location: Florida
Posts: 1,553
|
Re: EZ GO Workhorse runs, but does not move
Is it in gear ?
If it is in forward, you should be able to...with the engine off, 'roll' the cart by turning the rear (driven) clutch by hand in a counter clockwise movement. If it is in reverse, it will roll backwards if you turn the rear (driven) clutch by hand in a counter-clockwise movement. nevermind.. I don't know what I am talking about. |
11-06-2009, 08:49 AM | #5 |
Not Yet Wild
Join Date: Nov 2009
Posts: 4
|
Re: EZ GO Workhorse runs, but does not move
Yes, its in gear. I'll confirm to see if I can move the cart forward or backwards by turning the driven clutch by hand.
|
11-06-2009, 08:57 AM | #6 |
Gone Crazy
Join Date: Jan 2007
Location: Chesterfield, Va
Posts: 6,021
|
Re: EZ GO Workhorse runs, but does not move
If the driven (back) clutch turns and the wheels dont, remove the shift cables and manually move the shifter from forward to reverse.
It might not be engaging 100%. After that, I'm not sure if your cart has 1 piece axles or hubs, if it has hubs, make sure the hubs is not spinning on the axle. If a one piece axle, time to go inside! Keep us posted. |
11-06-2009, 04:54 PM | #7 | |
Love my Big Block
Join Date: Oct 2009
Location: Florida
Posts: 1,553
|
Re: EZ GO Workhorse runs, but does not move
Quote:
and the wheels don't engage..it has to be in the rear end..or the axles are spinning. If I roll the assembly, and the wheels DO engage forward and reverse, then the clutch is not grabbing the belt, it seems. |
|
11-06-2009, 05:15 PM | #8 |
Gone Crazy
Join Date: Jan 2007
Location: Chesterfield, Va
Posts: 6,021
|
Re: EZ GO Workhorse runs, but does not move
Well, you say when you rev up the motor the drive clutch turns the belt and that turns the driven clutch and they cycle open and closed so they are doing what they are supposed to do.
Either the driven clutch is spinning on the input shaft, your not going fully in gear, an axle is spinning in the hub(if it has them), or it is broke internally. |
11-06-2009, 05:16 PM | #9 |
Gone Wild
Join Date: Mar 2008
Location: Rockwall, Texas (Dallas / Ft. Worth)
Posts: 7,077
|
Re: EZ GO Workhorse runs, but does not move
You have a stripped rear brake hub.................
Run the cart in gear and look down at the rear tires - I'll bet you see one with a slight "wobble", that will be to one with the bad hub. Don't run it too long, as you can damage the axle. |
|
|
11-06-2009, 05:22 PM | #10 |
Gone Crazy
Join Date: Jan 2007
Location: Chesterfield, Va
Posts: 6,021
|
Re: EZ GO Workhorse runs, but does not move
I just reread your first post where you,ve been all through it all, checked hubs and all.
Your second post states the clutches are working as they should. Pull the driven clutch back off and check for a missing shaft key. |
|
|
Similar Threads | ||||
Thread | Forum | |||
Runs 10 minutes then shuts off, wait 5 then runs again... | Electric EZGO | |||
Reverse...runs awesome Forward..runs bad | Gas EZGO | |||
EZGO J402 motor runs but cart won't move | Electric EZGO | |||
97 Ezgo Motor runs but will not move | Gas EZGO |