|
|
|||||||
| Electric Club Car Electric DS, and Precedent golf cars |
  |
|
|
Thread Tools | Display Modes |
01-24-2019, 05:58 PM
|
#1 |
|
Gone Wild
 Join Date: Aug 2016
Posts: 612
|
2005 Precedent w/ new motor swap not moving....
49.9 volts in the system and I’m getting a solenoid click and the handheld is only throwing a “motor stall code”. Field current stays at 8.0 even after pedal is pressed and solenoid clicks; however “arm current” rises to as high as 361; “ARM PWM” stays at 0; “FIELD PWM” rises to as high as 97 and after about 3-4 seconds after the solenoid clicks all of these parameters drops back to zero with the exception of the field current. Also pack voltage rises from 49.9 to 51.1. Any suggestions?? Thanks in advance
Sent from my iPhone using Tapatalk |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
01-24-2019, 06:32 PM
|
#2 |
|
Bonafide Nincompoop
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 8,987
|
Re: 2005 Precedent w/ new motor swap not moving....
Reason the motor was removed?
Can you hear the motor try to move at all? Almost sounds like field wires are swapped or there's something physically jamming the armature. Did you happen to spin the input shaft by hand to make sure the transaxle isn't seized? |
|
|
|
|
01-24-2019, 06:37 PM
|
#3 | |
|
Gone Wild
Join Date: Aug 2016
Posts: 612
|
Re: 2005 Precedent w/ new motor swap not moving....
Quote:
I haven’t dug into yet just surface observations. Motor was swapped because the last one locked up for unknown reasons. Field wires as in the F2 and S2? Motor isn’t trying to turn at all but the cart will roll. Motor is suppose to be brand new (it looks it) I will try and take it off tomorrow and see if anything looks odd. Sent from my iPhone using Tapatalk |
|
|
|
|
|
01-24-2019, 09:15 PM
|
#4 |
|
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: 2005 Precedent w/ new motor swap not moving....
Test the output from the controller to the motor. Also get a spare battery and test run the motor itself why it is out to ensure it is working correctly.
|
|
|
|
|
01-25-2019, 03:27 PM
|
#5 |
|
Gone Wild
Join Date: Aug 2016
Posts: 612
|
Re: 2005 Precedent w/ new motor swap not moving....
Upon further testing it turns out that it was the controller. Not sure exactly what was done by the customer but there was some internal failure caused by something they did. After replacing it it’s now working fine. Let’s hope it stays that way [emoji1695][emoji1695]
Sent from my iPhone using Tapatalk |
|
|
|
|
01-25-2019, 11:44 PM
|
#6 |
|
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,477
|
Re: 2005 Precedent w/ new motor swap not moving....
Perfect!
 |
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| 2005 Club Car Precedent Won't start moving on its own | Electric Club Car | |||
| 2005 36 Volt EZ GO TXT PDS Motor Swap | Electric EZGO | |||
| Why not just swap a 48v motor for a 36v on my Precedent? | Electric Club Car | |||
| 2005 gas club car precedent,,motor won't turn over | Gas Club Car | |||
| 2005 Club Car Precedent Electric Not Moving | Electric Club Car | |||
Linear Mode
