|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
09-04-2020, 06:35 PM
|
#21 |
|
Not Yet Wild
Join Date: Aug 2020
Posts: 48
|
Re: 97 txt replaced motor but still wont go
So on step 2 of the diagram you posted, I had 14.4 volts. I went inside, came back out and now it only reads 1.2 volts. I cannot get it to read more. What would this mean?
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
09-04-2020, 06:38 PM
|
#22 |
|
Not Yet Wild
Join Date: Aug 2020
Posts: 48
|
Re: 97 txt replaced motor but still wont go
I pulled the cable off and put it back on and it read 14.2 then went back to 0.70.
|
|
|
|
|
09-04-2020, 06:53 PM
|
#23 |
|
Not Yet Wild
Join Date: Aug 2020
Posts: 48
|
Re: 97 txt replaced motor but still wont go
Okay, I have found out more. If I put it in tow mode for a few minutes and then go to run, then read the wire its 14.28volts. After 2 minutes it goes to 1volt.
|
|
|
|
|
09-08-2020, 09:07 AM
|
#24 |
|
Not Yet Wild
Join Date: Aug 2020
Posts: 48
|
Re: 97 txt replaced motor but still wont go
Should the voltage be steady on step 2 or is this normal?
|
|
|
|
|
09-08-2020, 10:02 AM
|
#25 | |
|
Techno-Nerd
 Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 97 txt replaced motor but still wont go
Quote:
Try measuring the voltages at the ITS sensor. |
|
|
|
|
|
09-09-2020, 08:35 AM
|
#26 |
|
Not Yet Wild
Join Date: Aug 2020
Posts: 48
|
Re: 97 txt replaced motor but still wont go
Step 2 gave me 14.2v. Removing the 6 pin connector on step 3 and testing gave me 14.7v.
It did go up. Based on this do you think the ITS is shot? I was unable to lift the cart and do the final test. The ITS seems to be a cheap part compared to the controller. So far the controller seems to have passed. |
|
|
|
|
09-19-2020, 01:56 PM
|
#27 |
|
Not Yet Wild
Join Date: Aug 2020
Posts: 48
|
Re: 97 txt replaced motor but still wont go
I replaced the its as it was damaged and cracked once I opened the cover. My cart still won't move. Do I replace the controller now?
|
|
|
|
|
09-19-2020, 02:07 PM
|
#28 | |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 97 txt replaced motor but still wont go
Quote:
Get an Alltrax XCT48x00-DCS. (X is for 3, 4 or 5 - meaning 300A, 400A or 500A version of the XCT controller.) |
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| speed sensor replaced now wont run | Electric Club Car | |||
| 96 yamaha replaced solenoid still wont go | Electric Yamaha | |||
| Replaced bad battery but cart wont last | Electric EZGO | |||
| Replaced batteries and cart wont run | Electric EZGO | |||
| replaced belt, now cable gets hot, wont start | Gas Club Car | |||
Linear Mode
