|
05-16-2011, 09:38 AM
|
#1 |
|
Getting Wild
Join Date: May 2011
Location: South GA
Posts: 110
|
spindle washers
Should there be any play at all in the spindle when the front of cart is lifted up? Mine had a good bit of play in it so I think I need to replace the washers at the top and bottom. I thought it was bushings but now I think it is just washers. Do I need to replace the bolt as well or just the washers?
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
05-16-2011, 09:59 AM
|
#2 |
|
The Last Moja Morani
 Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: spindle washers
check tnhe bolt when you take them out, if its worn yes replace it.......any grease fittings? try and grease it that should tighten it up a bit....................
 |
|
|
|
|
05-16-2011, 10:02 AM
|
#3 |
|
Getting Wild
Join Date: May 2011
Location: South GA
Posts: 110
|
Re: spindle washers
I guess I should go ahead and get the bolt too while I am getting the washers and save my self as trip.
|
|
|
|
|
05-16-2011, 10:03 AM
|
#4 |
|
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: spindle washers
they arn,t expensive and won,t hurt to put them in.......................
|
|
|
|
|
05-16-2011, 10:09 AM
|
#5 |
|
Getting Wild
Join Date: May 2011
Location: South GA
Posts: 110
|
Re: spindle washers
Haven't ever done this before. Is there anything else in there that would need replacing like a sleeve or anything?
|
|
|
|
|
05-16-2011, 10:14 AM
|
#6 |
|
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: spindle washers
i beleive there might be some bronze bearings they call them on the top side and besides the washers there are thrust washers.......................
|
|
|
|
|
05-16-2011, 05:08 PM
|
#7 |
|
Gone Wild
Join Date: Nov 2009
Location: Boondocks, MS
Posts: 693
|
Re: spindle washers
what you need is 2 kingpins and 4 bushings.......its not a bolt
|
|
|
|
|
05-16-2011, 05:21 PM
|
#8 |
|
Gone Crazy
Join Date: Jan 2007
Location: Chesterfield, Va
Posts: 6,021
|
Re: spindle washers
It really depends on what cart you have but most common ezgo axles have a bolt that goes through a big sleave that the splindle turns on.
A little up and down motion is normal when the cart is jacked up and no load on spindles. Need to replace the sleaves when you can hold the top and bottom of the wheel and rock it back and forth, just make sure if it rocks it is not loose wheel bearings. |
|
|
|
|
05-17-2011, 08:27 AM
|
#9 | |
|
Getting Wild
Join Date: May 2011
Location: South GA
Posts: 110
|
Re: spindle washers
Quote:
|
|
|
|
|
|
05-18-2011, 12:48 PM
|
#10 |
|
Getting Wild
Join Date: May 2011
Location: South GA
Posts: 110
|
Re: spindle washers
I think there is supposed to be bushings (washers) at the red arrows but it also looks like there are washers at the yellow arrows too. Is this right or what?
|
|
|
|
 |
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Do I need a new spindle or what? | Electric Club Car | |||
| Help with washers on Jakes LT for CC | Lifted Golf Carts | |||
| Differential Shim Washers? | Electric Club Car | |||
| Lock Washers on Battery Post | Electric golf carts | |||
| need help getting the spindle off | Electric Club Car | |||
Linear Mode
