ezgo dcs grind

scottyb · 07-11-2011, 09:20 PM

Quote:

Originally Posted by rib33024

Thats where the bearings are, look in my post at # 24--25, or in scotty's post # 26

#25 = intermediate shaft bearings....
#15 & 16 = input shaft bearings ...
#26 = carrier bearings

mistermnkim · 07-11-2011, 09:30 PM

Yes I see that! When I pull the input shaft will both bearing come out with it? Im sure they do just curious

Does anyone sell a complete bearing kit for my rearend?

mistermnkim · 07-12-2011, 01:17 PM

ok men need some more help, I pulled the motor off and took the snapring off the imput shaft assy but this bad boy will not come out, whats the trick? there is no notch for a slide hammer i have used visegrips and prybars with no luck. I thought about welding something on the end or drilling a hole on the other end and driving it out? what about putting the heat gun on it? HELP!!
I do think this is the problem for sure will only turn a little by hand i can make it turn over with plyers, the middle gears look good so im almost sure its the top assy. Thanks

mistermnkim · 07-12-2011, 06:45 PM

Ok I got the top shaft and bearing assy out!! Thanks scottyb

I have the 21spline shaft the inner bearing was fine but the outer bearing was toasted, rusted all up and hard to turn. I really hope the middle shaft bearing are ok it spins fine but untill i put a load on them. I really should replace them all I guess? just hate to fool with the freeze plug design lol
please give me your thoughts, should I just replace what I know is bad and see what happens?

mistermnkim · 07-12-2011, 06:50 PM

forgot here are some pics!! almost looks like this cart was under water, hmm just my luck katrina?? lol oh well im in now cant turn back and at least Ill know what ive got after I replace EVERYTHING.....

custom carts · 07-12-2011, 06:58 PM

now that you have it all out i would replace all the bearings then you are good to go the bearings are not expensive

mistermnkim · 07-12-2011, 08:18 PM

yes your right, I just ordered all new bearing and a input shaft kit, not real sure how the middle shaft comes out? Ill get the plugs out and figure it out! wish me luck!!

gornoman · 07-12-2011, 09:57 PM

Best of luck! Keep the pix coming, we need good pix on this service.

scottyb · 07-12-2011, 11:55 PM

Glad I could help you , where ever you are buying your parts get the freeze plugs too, they are cheap and it beats hell out of repairing the old ones and reusing them.

mistermnkim · 07-14-2011, 07:35 PM

Ok men I got the middle gear and bearing out today, noy too bad at all knock the plugs out get the snaprings off and tap the bearing out. All my parts should be here tomorrow by 2nd day air! wanted everything for this weekend

here are a few pics... oh also a pic of my first custom upgrade!! lol

07-11-2011, 09:30 PM	#12
mistermnkim Not Yet Wild Join Date: Jun 2011 Location: Greenville Ms Posts: 65	Re: ezgo dcs grind Yes I see that! When I pull the input shaft will both bearing come out with it? Im sure they do just curious Does anyone sell a complete bearing kit for my rearend?

07-12-2011, 01:17 PM	#13
mistermnkim Not Yet Wild Join Date: Jun 2011 Location: Greenville Ms Posts: 65	Re: ezgo dcs grind ok men need some more help, I pulled the motor off and took the snapring off the imput shaft assy but this bad boy will not come out, whats the trick? there is no notch for a slide hammer i have used visegrips and prybars with no luck. I thought about welding something on the end or drilling a hole on the other end and driving it out? what about putting the heat gun on it? HELP!! I do think this is the problem for sure will only turn a little by hand i can make it turn over with plyers, the middle gears look good so im almost sure its the top assy. Thanks

07-12-2011, 06:45 PM	#14
mistermnkim Not Yet Wild Join Date: Jun 2011 Location: Greenville Ms Posts: 65	Re: ezgo dcs grind Ok I got the top shaft and bearing assy out!! Thanks scottyb I have the 21spline shaft the inner bearing was fine but the outer bearing was toasted, rusted all up and hard to turn. I really hope the middle shaft bearing are ok it spins fine but untill i put a load on them. I really should replace them all I guess? just hate to fool with the freeze plug design lol please give me your thoughts, should I just replace what I know is bad and see what happens?

07-12-2011, 06:58 PM	#16
custom carts THE CUSTOM KID Join Date: Oct 2008 Location: Tallahassee Florida Posts: 820	Re: ezgo dcs grind now that you have it all out i would replace all the bearings then you are good to go the bearings are not expensive

07-12-2011, 08:18 PM	#17
mistermnkim Not Yet Wild Join Date: Jun 2011 Location: Greenville Ms Posts: 65	Re: ezgo dcs grind yes your right, I just ordered all new bearing and a input shaft kit, not real sure how the middle shaft comes out? Ill get the plugs out and figure it out! wish me luck!!

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

07-12-2011, 09:57 PM	#18
gornoman Stay thirsty my friends! Join Date: Jan 2007 Location: Suburban Chicago Posts: 24,286	Re: ezgo dcs grind Best of luck! Keep the pix coming, we need good pix on this service.

07-12-2011, 11:55 PM	#19
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,410	Re: ezgo dcs grind Glad I could help you , where ever you are buying your parts get the freeze plugs too, they are cheap and it beats hell out of repairing the old ones and reusing them.