|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
11-07-2016, 06:57 PM
|
#21 |
|
Happy Carting
 Join Date: Dec 2007
Location: Southern California
Posts: 73,408
|
Re: ezygo won't go
And I understand that not precharging the capacitors shortens the cap's life also
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
11-07-2016, 07:00 PM
|
#22 |
|
Not Yet Wild
Join Date: Nov 2016
Location: South Carolina
Posts: 25
|
Re: ezygo won't go
Thanks, cgtech for imput. I am beginner at this and struggling somewhat to understand what and how. Are you saying by removing resistor that V will drop from 36.5V to 0V? My other question is why do I get identical voltage readings with the switch and the F/R on or off?
Last edited by humptydump; 11-07-2016 at 07:01 PM.. Reason: Spelling |
|
|
|
|
11-07-2016, 07:07 PM
|
#23 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: ezygo won't go
Because the solenoid is only On when the pedal is pressed. (and all pre-qualifications are met like key on, f&r in a F or R position, charger not plugged in).
|
|
|
|
|
11-07-2016, 07:08 PM
|
#24 |
|
Not Yet Wild
Join Date: Nov 2016
Location: South Carolina
Posts: 25
|
Re: ezygo won't go
why do I get identical voltage readings with the switch and the F/R on or off? and pedal not depressed
|
|
|
|
|
11-07-2016, 09:09 PM
|
#25 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,408
|
Re: ezygo won't go
Because you wont take the precharge resistor off ?
|
|
|
|
|
11-07-2016, 09:23 PM
|
#26 |
|
Gone Wild
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,544
|
cgtech in post #20 explained it clearly. The resistor provides just a little power across the solenoid to keep the capacitors in the controller full. Not enough to make it run. That is why you have voltage on both sides. To test the solenoid like Scotty said remove the resistor.
Sent from my SM-G930R4 using Tapatalk |
|
|
|
|
11-07-2016, 10:04 PM
|
#27 |
|
Not Yet Wild
Join Date: Nov 2016
Location: South Carolina
Posts: 25
|
Re: ezygo won't go
Thanks! Will try tomorrow. Nite
|
|
|
|
|
11-09-2016, 08:25 AM
|
#28 |
|
Not Yet Wild
Join Date: Nov 2016
Location: South Carolina
Posts: 25
|
Re: ezygo won't go
Changed solenoid and have same issue. Where do I go from here and how? Thanks
I found a broken wire on something that goes from the two post on top of controller. Small wire with a yellow round/flat thing in center??? Help What is this? Last edited by humptydump; 11-09-2016 at 12:09 PM.. Reason: Added info. |
|
|
|
|
11-09-2016, 07:06 PM
|
#29 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: ezygo won't go
It's a MOV, and is not necessary for operation. If it's in question, remove it and try again.
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| 2004 gas txt ezygo ute barely drives | Gas EZGO | |||
| Ezygo 1983 Marathon | Gas EZGO | |||
Linear Mode
