Alltrax48500 and CC92FHD F/R hook up help !!!

[Ms506s]

Hey all, starting a new post. First one didn't make much sense. I will try to explain this as easily as possible because I'm a newb.

1. I have the controller 48500 mounted and hooked up to the heavy duty solenoid. Here is what I have going to what.

1. A1 post from motor is going to controller B+ terminal. I have another cable paired with that post of B+ going to the solenoid and from the other side of the solenoid to the fuse that it came with and to the battery.

2. From the B- from controller I have a wire going to a - Battery post.

3. S1 and S2 are going to the F/R Switch. M- on F/R is going to the M- on the controller.

4. A2 has no home right now, not sure where to bring it.

5. A2 shows to go on the F/R switch from the Altrax diagram. The HD F/R Switch I have doesn't have a post for A2. Only A1 on the bottom two posts of the F/R switch and on the picture it looks like it has a bar that goes between the two posts that I don't have or it didn't come with. So if A1 shows from Alltrax it is supposed to go to the B+ Terminal on the controller (which it is now) what the heck do I do with the A2 set up I am left with? No home!

Any help would be awesome, trying to get this done and I am lost.

[Ms506s]

Some pics image.jpg

[Ms506s]

More pics

[Jimbo2012]

You need some heat shrink on those cables

[Ms506s]

Originally Posted by Jimbo2012

You need some heat shrink on those cables

Will do

Do you know anything avout the rest of the post

[Aflyer]

Ms506s,
I feel your pain, this upgrade can be a little daunting for those of us who do not fully understand the technology.

I did a similar upgrade to mine recently but with an SW182 reversing contactor. It took me four or five emails with Scotty to get my wiring done.

I would send him an email and ask him where the A2 connection should go on the F & R switch you have.

Or maybe he will be on-line after the holiday to help you out.

Aflyer

[scottyb]

Originally Posted by Ms506s

Hey all, starting a new post. First one didn't make much sense. I will try to explain this as easily as possible because I'm a newb.

1. I have the controller 48500 mounted and hooked up to the heavy duty solenoid. Here is what I have going to what.

1. A1 post from motor is going to controller B+ terminal. I have another cable paired with that post of B+ going to the solenoid and from the other side of the solenoid to the fuse that it came with and to the battery. correct

2. From the B- from controller I have a wire going to a - Battery post. correct

3. S1 and S2 are going to the F/R Switch. M- on F/R is going to the M- on the controller. correct

4. A2 has no home right now, not sure where to bring it. A2 goes to the bottom terminal marked A1 on the diagram

5. A2 shows to go on the F/R switch from the Altrax diagram. The HD F/R Switch I have doesn't have a post for A2. Only A1 on the bottom two posts of the F/R switch and on the picture it looks like it has a bar that goes between the two posts that I don't have or it didn't come with. So if A1 shows from Alltrax it is supposed to go to the B+ Terminal on the controller (which it is now) what the heck do I do with the A2 set up I am left with? No home!

Any help would be awesome, trying to get this done and I am lost.

I hope this clears it up.

[Ms506s]

Originally Posted by scottyb

I hope this clears it up.

So Connect A2 to the A1 post on f/r switch? Bingo, bango? Is there supposed to be a bar or something to go in between the two posts?

[FireFighterHill]

The bar gives you full speed reverse.

[Ms506s]

So it's not necessary