|
05-23-2020, 09:55 AM
|
#1 |
|
Gone Wild
 Join Date: Oct 2008
Location: Ky
Posts: 241
|
Solenoid
Will a 36 volt solenoid work on a 48 volt cart?
Also I am having a hard time finding the procedure for testing the controller. Its a 2008 ez go RXV. Last edited by oncearacer52; 05-23-2020 at 09:59 AM.. Reason: Add to iy. |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
05-23-2020, 10:15 AM
|
#2 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Solenoid
A 2008 rxv came with a 36v solenoid from the factory, so, in your situation yes, a 36v solenoid will work on your 48v cart.
Search button top right area, then "danaher rxv troubleshooting guide" |
|
|
|
|
05-23-2020, 10:42 AM
|
#3 |
|
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Solenoid
thx
|
|
|
|
|
05-23-2020, 11:40 AM
|
#4 |
|
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Solenoid
Another thing, Is there a way to unhook motor wires and then run the motor with a jumper(s) from the battery?
|
|
|
|
|
05-23-2020, 12:08 PM
|
#5 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Solenoid
Batteries dont hold AC power, and you have a AC motor, so no, you cant do that.
|
|
|
|
|
05-23-2020, 01:48 PM
|
#6 |
|
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Solenoid
I just realized it is an ac motor a few minutes ago. I unhooked the three wires going to the motor at the controller. All wires check shorted to each other. I didn't think that is right. Motor bad? I also unplugged all plugs to motor while doing this.
|
|
|
|
|
05-23-2020, 03:19 PM
|
#7 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Solenoid
Apparently you have not downloaded & read "danaher rxv troubleshooting guide" as I suggested above. You would know the ohm values of your motor leads if you had.
|
|
|
|
|
05-23-2020, 03:59 PM
|
#8 |
|
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Solenoid
I did download it. I will look.
|
|
|
|
|
05-23-2020, 04:16 PM
|
#9 |
|
Gone Wild
Join Date: Oct 2008
Location: Ky
Posts: 241
|
Re: Solenoid
It appears that motor is bad. Going to recheck. Thx for the help.
|
|
|
|
|
05-23-2020, 07:08 PM
|
#10 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Solenoid
Well, I have only once seen failed windings in a rxv motor, and it was damaged by acid intrusion. You might want to be "very very sure", a new motor is around $1000
|
|
|
|
 |
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Solenoid Not Clicking after installing new Batteries and new Solenoid | Electric EZGO | |||
| 1989 Club Car DS 36v -New Vglide/Solenoid/microswitches Only moves when solenoid jump | Electric Club Car | |||
| Wrong Solenoid in my cart? w/ Pics- Please suggest correct solenoid I should be using | Electric EZGO | |||
| Solenoid not engaging with Forward / Reverse switch? (Solenoid is good) | Electric EZGO | |||
| Help converting G1 solenoid setup to single G16 solenoid | Gas Yamaha | |||
Linear Mode
