08-26-2015, 07:37 PM | #11 |
Gone Wild
Join Date: Dec 2009
Location: Corpus Christi, TX
Posts: 1,644
|
Re: 1999 Club Car clone swap - Jack Shaft Help
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-26-2015, 07:46 PM | #12 |
Not Yet Wild
Join Date: Mar 2011
Posts: 9
|
Re: 1999 Club Car clone swap - Jack Shaft Help
10 tooth
Tsubaki 50B10F-1 Finished Bore Sprocket, Single Strand, Inch, #50 ANSI No., 5/8" Pitch, 10 Teeth, 1" Bore: Roller Chain Sprockets: Amazon.com: Industrial & Scientific
12 tooth
Tsubaki 50B12F-1 Finished Bore Sprocket, Single Strand, Inch, #50 ANSI No., 5/8" Pitch, 12 Teeth, 1" Bore: Roller Chain Sprockets: Amazon.com: Industrial & Scientific
16 tooth
Tsubaki 50B16F-1 Finished Bore Sprocket, Single Strand, Inch, #50 ANSI No., 5/8" Pitch, 16 Teeth, 1" Bore: Roller Chain Sprockets: Amazon.com: Industrial & Scientific
18 tooth
Tsubaki 50B18F-1 Finished Bore Sprocket, Single Strand, Inch, #50 ANSI No., 5/8" Pitch, 18 Teeth, 1" Bore: Roller Chain Sprockets: Amazon.com: Industrial & Scientific
I didnt look for any pulleys for belts. What size is the shaft to the rear end? Will that need an adapter also? |
08-26-2015, 07:50 PM | #13 |
Not Yet Wild
Join Date: Mar 2011
Posts: 9
|
Re: 1999 Club Car clone swap - Jack Shaft Help
18 tooth
Tsubaki 50B18F-1 Finished Bore Sprocket, Single Strand, Inch, #50 ANSI No., 5/8" Pitch, 18 Teeth, 1" Bore: Roller Chain Sprockets: Amazon.com: Industrial & Scientific
16 tooth
Tsubaki 50B16F-1 Finished Bore Sprocket, Single Strand, Inch, #50 ANSI No., 5/8" Pitch, 16 Teeth, 1" Bore: Roller Chain Sprockets: Amazon.com: Industrial & Scientific
12 tooth
Tsubaki 50B12F-1 Finished Bore Sprocket, Single Strand, Inch, #50 ANSI No., 5/8" Pitch, 12 Teeth, 1" Bore: Roller Chain Sprockets: Amazon.com: Industrial & Scientific
10 tooth
Tsubaki 50B10F-1 Finished Bore Sprocket, Single Strand, Inch, #50 ANSI No., 5/8" Pitch, 10 Teeth, 1" Bore: Roller Chain Sprockets: Amazon.com: Industrial & Scientific
I didn't look for any belts or pulleys. What size is the rear end shaft? |
08-27-2015, 12:52 PM | #14 |
Gone Wild
Join Date: Dec 2009
Location: Corpus Christi, TX
Posts: 1,644
|
Re: 1999 Club Car clone swap - Jack Shaft Help
I don't know the shaft size
|
08-27-2015, 08:53 PM | #15 |
Gone Wild
Join Date: Dec 2012
Location: Dale, TX
Posts: 163
|
Re: 1999 Club Car clone swap - Jack Shaft Help
Look at zoro.com When I was looking for stuff they had everything I needed in the 250 to 300 range. Probably went a little on the big size for things but would rather have them a little too big than too small. I think I had a keyed shaft, sprockets, pillow block bearings, chain, master links, keys.
Leave the clutch on the motor unless you plan on running a 1 to 1 ration on your chain sprocket. http://www.buggiesgonewild.com/clone...get-build.html This is one of the best jack shaft jobs I have seen. |
08-27-2015, 09:02 PM | #16 |
Gone Wild
Join Date: Dec 2009
Location: Corpus Christi, TX
Posts: 1,644
|
Re: 1999 Club Car clone swap - Jack Shaft Help
Sea did you do a jack shaft setup?
Here's the me I was lookn for good info http://www.buggiesgonewild.com/clone...get-build.html |
Tags |
1999 club car, 420, clone, jack shaft |
|
|
Similar Threads | ||||
Thread | Forum | |||
club car clone swap | Clone Engine Swaps | |||
Club Car Clone swap | Clone Engine Swaps | |||
engine mount/jack shaft setup | Sled Engine Swaps | |||
where to get a jack shaft? | Design Center | |||
new pics of my workhorse with jack shaft and power steering | Gas EZGO |