|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
12-12-2009, 05:50 PM
|
#1 |
|
Not Yet Wild
Join Date: Jun 2009
Posts: 30
|
Help Needed 98 motor mount bolt size?
Hello All,
Picked up this 98 Ez-Go, it had a bit of a jerk when taking off - - I found that the front and rear motor mount bolts are missing out of the motor-all 4.  Anyone know the correct bolt size, length and thread for the 4 bolts? Thanks in advance! |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
12-12-2009, 08:04 PM
|
#2 |
|
Not Yet Wild
Join Date: Jun 2009
Posts: 30
|
Re: Help Needed 98 motor mount bolt size?
I know your thinking wtf- - so am I !
 |
|
|
|
|
12-12-2009, 08:53 PM
|
#3 |
|
Happy Carting
 Join Date: Dec 2007
Location: Southern California
Posts: 72,527
|
Re: Help Needed 98 motor mount bolt size?
 I am thinking I took 4 out last week but I have never measured them? THey were a 5/8 head so maybe a 3/8 bolt, coarse thread (18-20)? I dunno if they are metric or ASE? |
|
|
|
|
12-13-2009, 12:51 PM
|
#4 |
|
Gone Crazy
Join Date: Jan 2007
Location: Chesterfield, Va
Posts: 6,021
|
Re: Help Needed 98 motor mount bolt size?
They're 3/8-16, 1 1/2 or 2", flat washers and nyloc nuts. 9/16 wrenches
Should be able to pull one of the remaining bolts and measure length. |
|
|
|
|
12-13-2009, 01:09 PM
|
#5 | |
|
Not Yet Wild
Join Date: Jun 2009
Posts: 30
|
Re: Help Needed 98 motor mount bolt size?
Quote:
|
|
|
|
|
|
12-13-2009, 01:47 PM
|
#6 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 72,527
|
Re: Help Needed 98 motor mount bolt size?
I think the skid plate is an intregal part if the engine cradel support.... better check with MMT before you run it much and tear the motor in 2 somewhere
 Keep us posted...... |
|
|
|
|
12-13-2009, 02:51 PM
|
#7 |
|
Gone Wild
Join Date: Mar 2008
Location: Rockwall, Texas (Dallas / Ft. Worth)
Posts: 7,077
|
Re: Help Needed 98 motor mount bolt size?
There are 8 total bolts that hold the motor in. 2 in the front, 2 in the back and the 4 on the bottom. Bottom bolts go thru the skid plate, thru the front and back cradle and into the engine block.
Course thread - 5/8" headed bolt, so I'm thinking it's a 3/8"? Skid plate isn't necessary - but I wouldn't run one without it... |
|
|
|
|
|
|
|
12-13-2009, 03:55 PM
|
#8 |
|
Not Yet Wild
Join Date: Jun 2009
Posts: 30
|
Re: Help Needed 98 motor mount bolt size?
Thanks all-- just dropped it off at local cart mechanic.
|
|
|
|
|
12-13-2009, 04:20 PM
|
#9 |
|
Gone Wild
Join Date: Mar 2008
Location: Rockwall, Texas (Dallas / Ft. Worth)
Posts: 7,077
|
Re: Help Needed 98 motor mount bolt size?
Cart shop open on Sundays? Good move - Have them give it a good looksie
 |
|
|
|
|
|
|
|
12-13-2009, 05:50 PM
|
#10 | |
|
Not Yet Wild
Join Date: Jun 2009
Posts: 30
|
Re: Help Needed 98 motor mount bolt size?
Quote:
 |
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Wheel bolt pattern size? | Electric Club Car | |||
| Vanguard crank bolt size | Big Block Talk! | |||
| What size thread for Primary Puller Bolt? | Gas Yamaha | |||
| Briggs motor mount pic needed (for 93 ezgo marathon) | Big Block Talk! | |||
| 96 DS stock drive clutch bolt size (exterior bolt) | Gas Club Car | |||
Linear Mode
